Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

joining Melamine to form case

Posts

joining Melamine to form case

#1

joining Melamine to form case

Bob Fuller

>I am using 3/4" Melamine for the case of a bathroom vanity. Joining the bottom to the ends, I plan to use a 3/4" dado 1/4" deep with glue and the Melamine glue sold by McFeely.

I would welcome advise on that joint, but it is not my real problem.

Joining the back to the ends, I do not want the back to show at the end. Therefore, I plan a 3/4" x 1/2" rabbit with glue and comformat screws. The screws would go through the back and into the 1/2" dimension of the rabbit, and that has me concerned.

Is this advisable? Would a butt joint with screws into the back through the end panel be better? Or, perhaps I should use the rabbit but skip the screws?

Pardon me if this has been discussed here. I searched the archives for quite a while with no success.

Thanks for any help you can offer.

Bob Fuller

Fort Bragg, CA

Re: joining Melamine to form case

#2

Re: joining Melamine to form case

Fred Davis

>Bob,

I tried though my cabinet making aspect of building homes to stay completely away from Melamine, but thats just my personal bias.

If you put a top and bottom nail strip at the rear of the vanity , then fastening to these strips with the fastner of your choice , coupled with a clamped glueing of the sides to the back and you would be good to go.

if you go this way remember to set in the nailers the thickness of the back.

FredD

Re: joining Melamine to form case

#3

Re: joining Melamine to form case

Ken Platt (granby, CT)

>I made a couple of closet cases (essentially a box open in the front) from melamine. I used biscuits and RooClear melamine glue on a plain butt joint. They're maybe 4-5 years old and seem fine, and that's with a lot of stuff in and on them. For a bathroom cabinet, I'd use that again in a heartbeat. It's a lot easier than rabbets.

Ken

Re: joining Melamine to form case

#4

Re: joining Melamine to form case

Robby Wright

>I have done a few cases lately using Melamine with good results. First, be sure you get a good grade of Melamine. Some sheets are made with a course particle board and I don't recommend them. They fall apart or break easily and fasteners don't hold well.

For your back joint, I would make a rabbet that is 5/8" deep, then use the Confirmat screws to fasten on the back with a good glue. I recently found out the hard way that Titebond III does a decent job of sticking to Melamine. I accidently spilled some and let it sit, thinking I could just pop it off. Wrong. It really stuck. This was the Melamine with a little surface texture, not the glossy kind.

I have also found that with Confirmat screws, you don't need much of a dado to make a good joint. In fact, the opposite is true. I use a router bit to make an 1/8" groove, just enough to register the panel, then glue and screw the panel in place. I have one case I built this way that weights several hundred pounds in its own right and has several hundred more pounds of electronics in it. The case is on wheels and none of the joints have loosened in three years.

Robby Wright

San Marcos, CA

Re: joining Melamine to form case

#5

Thanks

Bob Fuller

>Thank you, fellows. I feel confident in moving ahead now.

Bob

Re: joining Melamine to form case

#6

Re: joining Melamine to form case

Frank Mutchler

>Bob, I have a kitchen full of 5/8" melamine boxes (full height) with hickory face frames and doors that all have simple butt joints held together with conformat type screws. Of course, I pre-drilled all the screw holes. The melamine is from a commercial lumber yard...not a big box store. The boxes themselves are pretty heavy and when full of canned goods or dishes they're real heavy. No problems at all in over 3 years and counting. As mentioned, you need to use commercial grade melamine.

Re: joining Melamine to form case

#7

One more thought...

Kris Lasure

>There are many ways to skin this cat. The most common way used in the casework industry is to use butt joints and dowels. In the way you are building your case, this would be a very easy way to do this. You don't even need a doweling jig. Just use some scrap material to make your own.

You can also use pocket screws and glue. I've done this on many cabinets and with good success. Just don't over torque the screws.

My personal way of building melamine cabinets is with confirmat screws. But the ends always get covered by another cabinet or laminate or veneer.

My backs are 1/4" thick that are set in 7/8" from the back edge of the sides panels and let into a 1/4" wide x 1/4" deep dado. I have a 3/4" nailer that goes in behind the 1/4" back that serves as a way to anchor the cabinet to the wall. Very typical cabinet construction.

Good luck with your project.

kl

Re: joining Melamine to form case

#8

Re: joining Melamine to form case

Frank Mutchler

>Using a 5/8" back eliminates the need for a nailer. Screw directly through it into the studs. I really like Danny Proulx's system of cabinet building. Minimizes waste and effort.