Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Upside down paint storage

Posts

Upside down paint storage

#1

Upside down paint storage

Pat Evans

>I read somewhere that paint cans stored upside down keep longer. I tried it with a can of satin poly, but I'm not convinced. Had to scrape the solids off the lid and try to get the poly remixed well. The results weren't good. Anybody use this technique?

Re: Upside down paint storage

#2

Re: Upside down paint storage

Gene Gauss

>I tried it with polyurethane. I got the skin that normally occurs, but this time the skin was under the poly instead of on top. That's probably better than the other way around, but I still had to strain it through a piece of window screen (I save it when I have to replace a piece). Tried it another time with some left over paint from spraying a car. Had it upside down on a shelf in my garage and after some time there noticed an stalactite of dried paint hanging from the shelf. I think the expansion and contraction of the air in the can because of the temperature changes in the (unheated) garage just pumped the paint past the lid seal. The flow was slow enough that the escaping paint dried as it flowed over the edge of the shelf.

Re: Upside down paint storage

#3

Buy The Smallest Can Available

George@Colonel's Workshop-Havertown PA

>Good Evening Pat,

I realized a long time ago that by buying the smallest can available, I usually minimized skin-over and subsequent wasted product. Should I have a little left over, I can toss it rather than worry about storage and skin-over. Nothing beats a fresh product, and after all the time spent making something to be proud about, applying old poly seems crazy to me.

George

Re: Upside down paint storage

#4

Re: Upside down paint storage

Alan in Little Washington (NC)

>Poly can be tough to keep- it starts to kick off in the presence of air and moisture (just like poly glue).

Not to steal the thread, but I was thinking, what about putting poly (and other finishes for matter) in a container similar to the new style baby bottles, but bigger- essentially a plastic liner inside a vented shell. As the baby drinks, the bag collapses- no take-up air gets into the bottle or the baby.

I would think paint would last a lot longer in a container like that, it would reduce waste, reduce the amount of air in the paint, reduce the loss of driers, be neater, cleaner, etc., etc.

It would require some other type of mixing since you couldn't stir it. You could mount a couple of containers, all having stop cocks on the bottom, in a vertically rotating rack. Each container would have a little ball weight in it that would fall (settle) from the bottom to the top to the bottom as the rack slowly rotates, stirring the finish. 10 min. before you are ready to paint, you turn on the motor that rotates the rack. When you are ready, turn off the motor and decant the amount of finish you need into your spray gun cup or into an open container if you will be using a brush.

What do you think? Should I call my patent attorney?

Re: Upside down paint storage

#5

Re: Upside down paint storage *LINK*

Alan in Little Washington (NC)

>By the way, my idea is similar to the 3M PPS (paint preparation system), except it is for the storage side.


3M PPS

Re: Upside down paint storage

#6

Don't know about upside down but...

Karen

>there's a way to prevent or at least minimize the skin formation.

Before closing up the can, set one side of the lid into the groove at the edge and hold the lid open about an inch. Take a deep breath and exhale into the can and quick close it up and tap it firmly in place.

The exhaled carbon dioxide will help prevent that dreaded skin.

I work with paints, stains and varnishes every single day and the only time I have skin formation on any paint or varnish is when the can has been unused for months at a time like with high-gloss poly. Nobody seems to want high-gloss poly for anything (which is fine by me :)

Re: Upside down paint storage

#7

Excellent advice

Pat Evans

>Yesterday I put on the first coat out of a new 1/2 pt. can of clear satin poly. That fixed all the problems in the old finish. I'll build up two or three more coats for protection and hopefully have these Christmas presents done before Christmas.

The old poly was the smallest can I could buy, I just kept it too long. I also think upside down storage was detrimental.

Re: Upside down paint storage

#8

Try this in your refrigerator

Al Goldstein

>This advice is usually given to keep foods in cardboard and plastic containers fresher longer in refrigerators. It works because the food blocks the air from coming into the container and no skin or any other chemical reaction occurs at the food/air interface.

In my house we have been using this technique for years in our refrigerator and it really works there. I had tried it with some paint in a large plastic jar, but the lid wasn't that tight and the paint leaked out. So I never tried it again with paint.

Hopes this helps someone.

Al

Re: Upside down paint storage

#9

Re: Try this in your refrigerator

Grant Wilkinson

>LV has collapsable plastic bottles that scrunch down to the level of the liquid in them. That way, there is a lot less air to cause degradation of any kind.

Re: Upside down paint storage

#10

Re: Upside down paint storage

Jesse

>In our family my wife does most of the finishing. She has found a technique to apply an artificial "skin" on the paint before closing the can. She uses the food grade plastic wrap that she uses in the kitchen. by pushing a piece of wrap down on top of the paint it effectively blocks the air and preserves the paint. Works for food in the refrigerator also. I'm not sure this will work for all types of finishes but certainly works for water based latex paints and finishes.

Re: Upside down paint storage

#11

Re: Upside down paint storage

Jerry Gibbs

>surprised nobody has mentioned Bloxygen. it is an inert gas sprayed into the top of the can. has worked for me. Jerry Gibbs