General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
O.T.: Searching multiple locations in craigslist *LINK*
by David Sparks 5/15/09, 4:52 PM
3 Replies · 54 ViewsLast post 5/15/09, 9:48 PM by Tates in Chesterfield, VA -
by Sawman 5/13/09, 8:44 PM
5 Replies · 22 ViewsLast post 5/15/09, 9:27 PM by John in NM -
by Phil Joines Krum, Tx 5/15/09, 7:26 PM
1 Reply · 12 ViewsLast post 5/15/09, 8:02 PM by Barry Irby -
OT - DudePerfect - AmazingBasketballShots *VIDEO*
by Mark Goodall - ATL - tooljunkie 5/15/09, 6:35 PM
0 Replies · 17 ViewsLast post 5/15/09, 6:35 PM by Mark Goodall - ATL - tooljunkie -
by Mark Mandell 5/15/09, 12:15 PM
4 Replies · 58 ViewsLast post 5/15/09, 2:49 PM by Ken Bellock (Houston, TX) -
Unsure about new Steel City experience
by Mike in NC 5/13/09, 4:17 PM
10 Replies · 39 ViewsLast post 5/15/09, 2:27 PM by Chuck in ND -
by Mark Mandell 5/13/09, 7:00 PM
6 Replies · 31 ViewsLast post 5/15/09, 10:55 AM by Mark Mandell - Gone Round In Jersey -
by GolfSteve in Calgary 5/14/09, 12:14 AM
11 Replies · 43 ViewsLast post 5/15/09, 3:15 AM by Victor Parisian -
by Chicago Bob 5/13/09, 5:52 PM
8 Replies · 20 ViewsLast post 5/15/09, 2:11 AM by Gerry Wittenberg in North Surrey -
by paul woolson 5/13/09, 3:39 PM
7 Replies · 66 ViewsLast post 5/15/09, 12:32 AM by Barry Irby -
by Thomas Skaggs 5/13/09, 3:20 PM
12 Replies · 43 ViewsLast post 5/14/09, 10:50 PM by Dale Lenz -
by Rod Rentz 5/13/09, 3:48 PM
5 Replies · 29 ViewsLast post 5/14/09, 10:02 PM by Ellis Walentine -
by Joanne in Pt. Pleasant, PA 5/13/09, 1:24 AM
18 Replies · 38 ViewsLast post 5/14/09, 8:29 PM by AZ, Colorado Springs -
Article applies to woodworkers, too *LINK*
by North of the Border 5/14/09, 4:45 PM
0 Replies · 44 ViewsLast post 5/14/09, 4:45 PM by North of the Border -
Router speed and speed control Q's
by Ed Wujciak 5/11/09, 1:45 AM
8 Replies · 25 ViewsLast post 5/14/09, 4:44 PM by North of the Border -
by Jerry Gibbs 5/14/09, 11:38 AM
1 Reply · 19 ViewsLast post 5/14/09, 3:15 PM by Bill Houghton -
by Fred West in West Chester, PA 5/13/09, 4:49 AM
3 Replies · 18 ViewsLast post 5/14/09, 2:48 PM by Fred West in West Chester, PA -
by Robert R. Clough - Thorncraft 5/13/09, 3:35 PM
2 Replies · 18 ViewsLast post 5/14/09, 2:04 PM by Dan Donaldson -
by steve mackay 5/12/09, 10:57 PM
6 Replies · 24 ViewsLast post 5/14/09, 1:55 PM by Chuck in ND -
by Dale Lenz 5/13/09, 10:29 PM
2 Replies · 16 ViewsLast post 5/14/09, 1:41 PM by BobS -
by Doug 5/14/09, 11:00 AM
3 Replies · 16 ViewsLast post 5/14/09, 1:28 PM by Jesper, Denmark -
by Don Orr 5/11/09, 2:17 PM
22 Replies · 66 ViewsLast post 5/14/09, 12:09 PM by Mark Goodall - ATL - tooljunkie -
Any help on how to repair a deep gouge in table?
by Juliet Robinson 5/13/09, 11:29 PM
4 Replies · 27 ViewsLast post 5/14/09, 11:58 AM by Ellis Walentine -
by Steve in East Tennessee 5/11/09, 11:57 PM
4 Replies · 26 ViewsLast post 5/14/09, 2:09 AM by Steve in East Tennessee -
by Woodie49 5/13/09, 3:53 PM
2 Replies · 26 ViewsLast post 5/14/09, 2:03 AM by Woodie49 -
by Jim Shaver - Oakville, Ont 5/9/09, 11:14 AM
11 Replies · 22 ViewsLast post 5/14/09, 12:04 AM by GalenV in Iowa -
connecting a bosch 3237 to a fein turbo II
by andre mallegol 5/13/09, 1:59 PM
6 Replies · 18 ViewsLast post 5/13/09, 9:04 PM by andre mallegol -
Jet 22/44 Oscillating Drum Sander
by david in indy 5/13/09, 5:50 PM
3 Replies · 27 ViewsLast post 5/13/09, 8:20 PM by JL -
Happy Birthday to A.J. Hamler!
by Alan Young 5/13/09, 12:39 PM
5 Replies · 17 ViewsLast post 5/13/09, 6:22 PM by Charlie Self -
by woodenleg 5/12/09, 11:54 PM
2 Replies · 16 ViewsLast post 5/13/09, 1:12 PM by Tom Dunlap



