General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
by Fred Davis 1/20/10, 8:21 PM
1 Reply · 13 ViewsLast post 1/20/10, 8:32 PM by Ellis Walentine -
by Dan Donaldson 1/20/10, 7:50 PM
0 Replies · 13 ViewsLast post 1/20/10, 7:50 PM by Dan Donaldson -
by Mark Mandell 1/20/10, 7:37 PM
0 Replies · 14 ViewsLast post 1/20/10, 7:37 PM by Mark Mandell - Gone Round In Jersey -
by Andy Wright 1/18/10, 3:23 AM
14 Replies · 38 ViewsLast post 1/19/10, 4:10 PM by Mark Mandell - Gone Round In Jersey -
Quarter sawn oak glue-ups - - - grain question
by Pete in Holland, MI 1/19/10, 2:07 AM
4 Replies · 23 ViewsLast post 1/19/10, 2:53 PM by Keith Newton------WebKitFormBoundaryV6MZb+tiOpocz6 -
by Stephen Shepherd 1/19/10, 1:41 PM
0 Replies · 15 ViewsLast post 1/19/10, 1:41 PM by Stephen Shepherd -
Freak microplane injury *LINK*
by JohnM in Mid Mich 1/18/10, 9:17 PM
10 Replies · 26 ViewsLast post 1/19/10, 5:16 AM by davhamm -
Sheet Goods Help------WebKitFormBoundary+RUqXCRNyX
by Gabe Doyle------WebKitFormBoundary+RUqXCRNyXmiX+nn 1/18/10, 5:06 PM
11 Replies · 37 ViewsLast post 1/19/10, 3:58 AM by Jim Dillon -
by Dan Donaldson 1/19/10, 1:56 AM
0 Replies · 14 ViewsLast post 1/19/10, 1:56 AM by Dan Donaldson -
Jet Dust Collector Motor bearing replacement
by Dave Paine 1/18/10, 1:33 AM
2 Replies · 66 ViewsLast post 1/19/10, 1:36 AM by Dave Paine -
Woodcentral Infected - False Alarm?
by North of the Border 1/17/10, 6:43 PM
18 Replies · 28 ViewsLast post 1/19/10, 1:36 AM by Alexandre Grigoriev -
by Tom MacGregor 1/17/10, 10:56 PM
7 Replies · 38 ViewsLast post 1/18/10, 11:45 PM by Larry in NW Ohio -
by quercus 1/18/10, 11:28 PM
0 Replies · 14 ViewsLast post 1/18/10, 11:28 PM by quercus -
Grain orientation for curved legs/feet
by Todd in VA 1/18/10, 3:04 AM
6 Replies · 31 ViewsLast post 1/18/10, 10:22 PM by Todd in VA -
WC Weekend Accomplishments....
by Dennis E Peacock 1/18/10, 2:52 PM
5 Replies · 24 ViewsLast post 1/18/10, 9:15 PM by Simon St.Laurent - Dryden, NY -
by Tom Henderson 1/17/10, 10:38 PM
9 Replies · 31 ViewsLast post 1/18/10, 9:06 PM by Bruce, a MN Galoot -
by Howard In Toronto 1/18/10, 6:42 PM
1 Reply · 10 ViewsLast post 1/18/10, 8:51 PM by Mark Mandell - Gone Round In Jersey -
by Tom MacGregor 1/17/10, 10:56 PM
7 Replies · 87 ViewsLast post 1/18/10, 8:34 PM by William Falberg -
by mamc 1/5/10, 5:43 PM
15 Replies · 32 ViewsLast post 1/18/10, 5:52 PM by mamc -
by Dustmaker Mike 1/18/10, 5:28 PM
0 Replies · 70 ViewsLast post 1/18/10, 5:28 PM by Dustmaker Mike -
by Dustmaker Mike 1/18/10, 9:27 AM
3 Replies · 12 ViewsLast post 1/18/10, 4:55 PM by Mark Mandell - Gone Round In Jersey -
Quality of Plywood Decreasing?
by Tom MacGregor 1/14/10, 10:56 PM
11 Replies · 35 ViewsLast post 1/18/10, 2:49 PM by Dan Donaldson -
Kinda OT - Stomach bug going around
by Stephen Kirk in Quakertown, PA 1/18/10, 9:04 AM
2 Replies · 14 ViewsLast post 1/18/10, 2:29 PM by Jason Roehl in Lafayette, IN -
by Barry Irby 1/17/10, 9:09 PM
2 Replies · 15 ViewsLast post 1/18/10, 1:22 PM by Lee Schierer - McKean, PA -
Maple Bloodwood Desk a la Modern (w/PIX) 2
by Hikmet C. Sakman 1/12/10, 6:42 AM
27 Replies · 69 ViewsLast post 1/18/10, 1:05 PM by David Yoho -
Performax 16-32 on Classified Board
by Joe Pack 1/18/10, 6:51 AM
0 Replies · 32 ViewsLast post 1/18/10, 6:51 AM by Joe Pack -
Joining two pieces of wood in a hat stand
by Stephen 1/18/10, 12:56 AM
3 Replies · 21 ViewsLast post 1/18/10, 3:35 AM by Phil Joines Krum,Tx -
by Jerry Draper 1/18/10, 2:33 AM
0 Replies · 31 ViewsLast post 1/18/10, 2:33 AM by Jerry Draper -
Mortiser setup with coins, where is that picture?
by Ray Carson - Lawrenceville, NJ 1/13/10, 3:45 PM
14 Replies · 52 ViewsLast post 1/18/10, 1:23 AM by North of the Border -
by David L. Frame Jr. 1/17/10, 6:39 PM
4 Replies · 20 ViewsLast post 1/17/10, 10:18 PM by Randy Johnson



