Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Sheet Goods Help------WebKitFormBoundary+RUqXCRNyX

Posts

Sheet Goods Help------WebKitFormBoundary+RUqXCRNyX

#1

Sheet Goods Help------WebKitFormBoundary+RUqXCRNyX

Gabe Doyle------WebKitFormBoundary+RUqXCRNyXmiX+nn

>Reading the thread below about the decreasing quality of plywood has me wondering what to build my next project out of.

I've got the design roughed-out for a mobile workbench/tool cabinet. The base cabinet is approx. 30"h x 60"w x 24"d and will be on four locking castors (not shown). The top is approx. 30" x 70". The three sections will be filled with some configuration of drawers.

Because the best plywood I can get at HD or Lowes turns into skateboard half-pipes within hours of getting it home, I've been thinking of doing it all out of MDF (the main reason behind the doubled-up end panels). I'm even thinking of doing the top in two layers of MDF, but mostly for cheap and easy replacement after it gets abused, although I'm also considering doing the top in maple and adding a vise.

Anyway, my thoughts are that MDF will be stable, but maybe not very strong - also very heavy. Should I be looking for something at an actual lumber yard that is still reasonably cheap, stable, strong, and not excessively heavy? Any ideas for design changes?

Gabe

Mesa, AZ

------WebKitFormBoundary+RUqXCRNyXmiX+nn


img

Re: Sheet Goods Help------WebKitFormBoundary+RUqXCRNyX

#2

Re: Sheet Goods Help------WebKitFormBoundary+RUqXC

Jesse Cloud

>You're on the right track. Forget about Lowe's and HD. Find a good lumberyard. Ask a local cabinet shop where they trade if you can't find a good supplier.

That's not a guarantee of quality, but it improves your odds a lot.

Re: Sheet Goods Help------WebKitFormBoundary+RUqXCRNyX

#3

Re: Sheet Goods Help------WebKitFormBoundary+RUqXC

paul in AZ------WebKitFormBoundary+isMX5X2paiDYC5e

>Gabe:

If you are in mesa you are right next door to a supplier I've used.

Timber Machinery on Southern Ave in mesa has a lumber yard in the adjacent building. They have a big selection of hardwoods and have sheet goods. Their prices are usually very good.

In fact i called on friday about 3/4' maple faced plywood [ which they have] for a low stand for a 42 inch TV. A quick and dirty low budget project.

Woodcraft on Eliott in Tempe has a more esoteric collection of lumbers and some sheet goods at generally higher prices.

No need to use the big box stores.

Re: Sheet Goods Help------WebKitFormBoundary+RUqXCRNyX

#4

correction

paul in AZ------WebKitFormBoundary+isMX5X2paiDYC5e

>That is Woodworker's Source on Elliot in Tempe.

Woodcraft is in Chandler but has relatively little in larger sheet goods.

Re: Sheet Goods Help------WebKitFormBoundary+RUqXCRNyX

#5

Re: Sheet Goods Help------WebKitFormBoundary+RUqXC

Roy Girolami------WebKitFormBoundary9yANUT8mn8C+Zo

>Gabe, for strength and quality, find some Baltic Birch plywood. I think it is metric sized about 19mm but it has maybe 10 layers and I've never had a void or a de-lamination. i always make my bookcases out of it.

Roy Girolami

Apex, NC

Re: Sheet Goods Help------WebKitFormBoundary+RUqXCRNyX

#6

Re: Sheet Goods Help------WebKitFormBoundary+RUqXC

xeddog

>I built something similar to that only a little longer, and it sagged badly. Based on that I would also suggest adding two more castors in the center.

xeddog

Re: Sheet Goods Help------WebKitFormBoundary+RUqXCRNyX

#7

Re: Sheet Goods Help------WebKitFormBoundary+RUqXC

David Hay @ Denver

>Can't help with the sheet good supplier, but I'd think about sagging in the middle...esp with something that long. Either put an additional set of casters in the middle, or bolt some angle iron to the bottom to help provide some additional rigidity.

David

Re: Sheet Goods Help------WebKitFormBoundary+RUqXCRNyX

#8

Sagging

Gabe Doyle

>I'd thought about the sagging issue and plan to use a 3/4" back, but attaching angle iron on the bottom would be a good idea too.

I think the additional castors would increase the chances of the cabinet wobbling - my garage floor is pretty flat, but not perfect.

Re: Sheet Goods Help------WebKitFormBoundary+RUqXCRNyX

#9

Re: Sheet Goods Help

Gabe Doyle

>Thanks - I've not been to Timber Machinery before. I think I'll try to get over there this week.

Re: Sheet Goods Help------WebKitFormBoundary+RUqXCRNyX

#10

Re: Sheet Goods Help

Gabe Doyle

>I've used baltic birch plywood before for some small projects, but if I remember correctly, it only came in 5'x5' sheets. Does it come in 4'x8' sheets?

Re: Sheet Goods Help------WebKitFormBoundary+RUqXCRNyX

#11

Re: Sheet Goods Help

Simon St.Laurent - Dryden, NY

>Baltic Birch is generally 5x5, but there's a similar product called ApplePly that comes in 4x8.

Re: Sheet Goods Help------WebKitFormBoundary+RUqXCRNyX

#12

Re: Sheet Goods Help------WebKitFormBoundary+RUqXC

Jim Dillon

>Gabe,

I think your plan and use of MDF is doable with some design changes. In fact, I built something very similar to what you are planning. Here is a picture of a lathe bench I made from double-walled MDF. The plan is from Shop Notes No. 67. I made my bench roughly 55 inches long with a top roughly 60 inches. The top was from three layers of MDF. Note the use of stretchers on the bottom, plus a solid cross piece under the drawers that extends the whole width of the cabinet. That, plus your back would help your cabinet resist racking. The plan also uses dado and rabbet joints throughout further strengthening the unit. With these design considerations, I've seen no sign of sagging. Keep in mind though that the use of MDF for the lathe bench was to provide great weight and to dampen vibration from the lathe. Personally, for just cabinets, I would try to find some good plywood as others have suggested. If you can't, then I hope this gives you some ideas.

Jim


img