Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Resaw Fence

Posts

Resaw Fence

#1

Resaw Fence

Tom MacGregor

>I got a riser block & a 3/4" Timberwolf blade for my 14" Grizzly bandsaw and threw together a 6" tall resaw fence to try it out. Cut a piece of 1/8" aluminum plate on my Homecraft bandsaw shown in my last post and screwed on a piece of scrap PVC pipe. Fast, cheap and it works. I plan to try a slightly heavier & taller one for wider stock.


img

Re: Resaw Fence

#2

Re: Resaw Fence

Barry Irby

>Looks great. Better than mine. I made one out of plywood and used a dowel for the "point" on the fence. I found that I had trouble with the round surface. If I put it directly beside the front of the teeth or slightly beyond them it was difficult to get started with the cut. The board would start to the left and want to translate to the right as it engaged the teeth. I sanded a flat surface about 3/16" long on the dowel. That could be set just in front of the teeth and made it much easier to set the gap/thickness and to get the cut started. Your pipe might be enough larger in diameter that this does not matter.

I also find a feather board on the table that keeps the workpiece pressed to the fence is very worthwhile/necessary. Actually, another one near the top might be good too, but I have not figured out how to set it up.

Re: Resaw Fence

#3

Ellis Walentine

Good tip, Barry

Ellis Walentine

>The idea of the "point fence" is to allow you to compensate manually for drift by having a limited point of contact with the fence. You described a problem that is built in with a round or pointed fence. A small flat wouldn't affect the performance of this kind of fence, but I can see how it would make it easier to start the cut. Good one.

Ellis

Re: Resaw Fence

#4

William Falberg

Re: Good tip, Barry

William Falberg

>I still don't understand why you built the fence when all you needed was a "leaning post"? And why didn't you run the post up to the blade guide extension bracket for support and vertical orientation?

Re: Resaw Fence

#5

Clint Searl

Re: Resaw Fence

Clint Searl

>Looks like your setup works perfectly.

Clint

Re: Resaw Fence

#6

Re: Resaw Fence

Stuart Hough

>Looks great Tom! I may steal your idea ;-)

Re: Resaw Fence

#7

You talkin' to ME?

Barry Irby

>Bill, I don't understand your post. First, Were you responding to my post or his?

My "fence" looks more like a shelf than a fence. It's two pieces of plywood at right angles to each other and one of them has a dowel stuck on it with a couple of brads. I sanded the flat on it because of the brads.

What is a "leaning post"?

Are you suggesting attaching the fence or leaning post to the blade guide/whatever at the top?

I wish I knew half of what you know about bandsaws. I use mine just often enough to be bad at it.

Re: Resaw Fence

#8

William Falberg

Re: Resaw Fence

William Falberg

>No, Barry, I was replying to the OP but screwed up (again) on the "reply" button. Sorryyyyy:@) I like your idea of putting a flat on the dowel, it's not my preferred solution for re-sawing, but under some conditions (like "exploring" found wood) it has a place; cleaner than free-handing anyway. It gives the operator a better visual reference and probably helps to steady your hands.

It's easy for me to attach the fence to the upper wheel housing and brace the frame to the table by screwing upward, as if to spread the frame, into a horizontal rail at the top. It totally eliminates any chatter from frame-flex and gives me adjustable parallelity to the blade in the most exact dimensions. I believe there are also attachment points on any saw that could connect this way and thought first about the blade guide extension brackets common to them all. Don't they all have a bolt or two in that area that could be attached to, and bracketed out, to meet the fence/post? There's no word for a full-length post like that so I made up "leaning post" because the workpiece is meant to lean against it the same way a workpiece "leans" against a fence. I don't know a better way to re-enforce fences against the inward push of feed pressure while rip-feeding tall pieces into the blade.

I think there's an after-market opportunity for the first ambitious ontrapanure that productizes a "floor-to-ceiling" modular fence system and the instructions to do so are in my upcoming book, along with how to build the whole darn saw if one were really ambitious. I'm into my own saws and don't really know much about the Delta clones so I leave it up to you guys.

There's a whole chapter on metal-work for woodworkers I hope you all read. These wooden fixtures gotta go. Aluminum is much easier to work than you think.