Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

paint booth question

Posts

paint booth question

#1

paint booth question

Andy Wright - Allen, TX

>I am thinking of building a paintbooth in my shop and wanted to see if anyone has already done something similar and can pass on any tips. I was looking at an outdoor patio at a restaurant and thought the concept of the roll-up walls with zippers would work for a booth.

My concept is to hang four "walls" made from 10mil plastic from the cieling with firing strips, and put zippers on the corners. When it is time to paint I just need to put a dropcloth down, roll down the sides, zip up the corners, and set up an exhaust fan. When the booth is not being used, I can roll the sides up out of the way and hang them from the ceiling.

Anyone have suggestions? Also, I am looking for zippers. All of the adhesive zippers I have found for use by contractors are 7 foot, but since I have a 10' ceiling in the shop I need something longer

Thanks in Advance

Re: paint booth question

#2

Clint Searl

Re: paint booth question

Clint Searl

>I tried something similar using big drop clothes hung from clipon hooks from LV. Without exhaust, the tent just fills up with solvent fumes and overspray. Gave it up and wait till it's warm enough to spray outside unless it's a small project.

Consider Velcro instead of zippers.

Clint

Re: paint booth question

#3

Re: paint booth question

AZ, Colorado Springs

>In the Air Force we had paint boths in both vehicle and aircraft maintenance. The paint booths were rigid rooms within the shop area, each big enough to fit a pickup truck or suburban into (we painted airplane parts, not entire planes -- but the manufacterers and depots have paint hangars for that).

The problem I see with your idea is that when you exhaust the air inside, either the walls collapse or different (dirty) air fills the enclosure.

Our paint boothes had two banks of filters: along one wall, they capture overspray from the soon-to-be exhausted air, and a similar bank of filters on the other end captures dirt out of the incoming air. The filters were sized for the airflow (CFM) of the exhaust fans. And the exhaust fans were sized to move enough fresh air to cure the paint properly and quickly.

What is your objective -- to protect the rest of your shop from overspray? ... enhance the finishing process? ... or something else?

Re: paint booth question

#4

Re: paint booth question

Andy Wright - Allen, TX

>The main purpose of the booth is to keep overspray and fumes out of the shop. I have sprayed several large projects directly in the garage, and aside from being messy I have also had problems with the fumes getting into the house.

I actually have a "booth" similar to the one I am describing built in my shop right now, but it is very temporary. I used light weight plastic sheeting (1.5mil) and tacked the top of the sheeting to the cieling temporarily with 1/4" staples. The bottom of the "walls" are weighed down with whatever I could find laying around (gallon paint cans, etc.) One wall of the booth is the garage door which is raised up a foot to allow the exhaust fan to blow outside. The setup has worked great, and I was thinking it would be nice to put in something a little more permanent that would be quick to set up in the future.

I like Clint's idea to use velcro instead of zippers - that would make it easier to put together, and I can get it in any length

Re: paint booth question

#5

Re: paint booth question

Tom MacGregor

>The exhaust system needs to be designed to keep the motor and any source of spark out of the airflow. A lot of that smelly stuff is flammable and the last thing you need is to ignite the fumes. I'd want to address all safety issues 100% before worrying about velcro vs. zippers.

Re: paint booth question

#6

Took a class and he had a solution !

Frank on Chestnut Hill

>I only shoot water based products... have a fan mounted in a homemade sleeve that just fits the window. It is held in place by a couple of bungie cords. I have 3 side walls made up from cheap shower curtains hung with large wire ties from pcs of pvc pipe. I have a oriental rug on the floor ( auction job, must have been 10$). It works. Have shot at least a hundred projects in there. The trick is ... positive air flow going out the window, and some coming in from a cracked window 180 degrees away. Cheap and functional!

Re: paint booth question

#7

Follow up..The instructor was Jerry Terhark!!

Frank on Chestnut Hill

>

Re: paint booth question

#8

Re: paint booth question

Mark Rakestraw

>Andy,

I use plastic sheeting for my spray booth. It's basically just two independent sheets that hang down and form a funnel towards a window fan on one wall. Something like this: >o except the points of the greater than sign don't meet, but come up to the wall on either side of the "0" which represents the window fan. The back side is completely open to allow the needed airflow for the exhaust fan to work. The window has a box built around it to hold a couple of furnace filters to help keep the fan clean. I use 3 mil plastic with a cleat on the top to hold it to the ceiling and a 1X1 cleat on the bottom to weight down the curtain. When not in use you just roll up each curtain and it takes up zero space. When the curtain gets too crusty you just pull it down and put up a new sheet. I use all waterborne finishes now, but have sprayed lots of solvent based finishes with this system without a problem. I will stop short of telling you you don't need an explosion proof fan, but I think for the home shop that akin to thinking you have to ground your plastic dust collection hose. You need a strong fan to move enough air that you are quickly clearing any overspray before it has the chance to settle on your workpiece. If you're moving that much air I don't think you can build up the concentrations of flammable vapors necessary to cause an explosion. I have sprayed solvent directly onto the filter box without a problem. As I said I'm not recommending you do this, YMMV and you may blow up. You can avoid this issue completely by switching to waterborne finishes. If you're interested I can snap a picture of it today and post it.

Mark

Re: paint booth question

#9

Re: paint booth question

del schisler

>i spray lacquer in the shop But i keep the shop clean I have a 36" exhaust fan where i spray I put it on low I have very little problum with dust Their are no over spray in the shop at all Like i said i keep the shop very clean Even when i sand i sand in frount of the exhaust fan All dust goes out The same when i use the table saw I have the fan on No dust from the sawing I leve the door open so i have lot of freash air comming in Before i spray i use the air comp. and blow all dust out Not a problum it is clean as it need to be Lot's of the time i use the air and blow all over the shop with air and i use the other 36" exhaust fan also I 2 of them I belive that is the only way to keep it very clean I live in florida so most of the time weather is good thanks for reading del

Re: paint booth question

#10

Fans

Mark Mandell - Gone Round In Jersey

>Someone will or should come in here and insist that you put in an explosion-proof fan ($4-600 that I've seen), and they'd be technically absolutely right if you're spraying solvent finishes.

But

I built my booth out of 1x2 firing strips and 7 mil sheeting. It is all KD in 3x8' sections and has ceiling panels as well. Exhaust is through a $20 20" box fan with spun-glass filters and the air inlet is a 24" square HEPA filter. I use a turntable to rotate the workpiece so I don't have to move around in the booth. Whole deal stores in a corner of the shop.

WAIT A MINUTE, MANDELL, WHAT ABOUT THAT EXPLOSION-PROOF FAN?

OK you got me, I don't use one, even though I spray shellac in the booth. However, turns out, my box fan is pretty close. Why? Well, 1) it runs on an induction motor so no sparking motor brushes + the cheapo motor bearings are nylon/teflon so no sparking there either, 2) the fan is plastic so no danger of a spark there, and 3) the switch, the only source of a spark, is actually (mostly) out of the air stream and is turned on before work starts and off only after all vapor is gone. So for 20 bucks I've got my issue solved for an occasional weekend warrior-type sprayer-dude. I could, of course, make it a touch safer by rewiring the switch completely outside the box housing.

This good in a commercial shop? ABSOLUTELY NOT, won't take the abuse, doesn't meet "CODE", and will void your shop insurance if the joint goes up even due to an unrelated cause.

Re: paint booth question

#11

Re: Fans

Andy Wright - Allen, TX

>I guess I will probably continue to "roll the dice" and use a regular fan instead of an explosion proof fan. Since I am using an hvlp gun, the overspray is pretty minor (nothing like the old fashioned cup gun I used to have that would create a "fog" of overspray).

Thanks for all of the tips - it has helped me get my ideas together.

On a side note about fans - my father has been in the autobody business for 35 years, and up until about 15 years ago he had never used a paint booth. I asked him about the fan and he kind of laughed saying that he painted and sprayed primer every day for 20 years using a WWII surplus motor to drive his exhaust fan. I remember that set-up -- it was definitely not exposion proof! Of course that was before OSHA took over the world, and I doubt that using a non-explosion proof fan probably was even near the top of the list of the "most dangerous" things about his shop in the 70's. In the mid 90s OSHA forced him to buy a $20,000 spray booth, and he will be the first to admit that it is a lot better than the "good old days". However he still knows a lot of people who shoot cars in their garages/shops using old fashined exhaust fans. As always, decisions about safety are something everyone has to make for themselves.

Re: paint booth question

#12

Guns

Mark Mandell - Gone Round In Jersey

>I've read several articles where guys shoot waterborne via HVLP right in their shops (no booth, etc.) and, they claim, don't get spray on anything because any mist dries to power before it gets to a surface. I get very little mist from my CA mini hvlp gun that I use for sealing and toning, but I still want the alcohol vented outside. I get more overspray with the big Walcom/pot rig, but then I do tend to apply a lot more material in a pass with waterbornes, so I still want the booth exhaust pulled through the glass filters which trap it and are good for two sessions.

Re: paint booth question

#13

Re: Guns

Andy Wright - Allen, TX

>I have sprayed directly in the shop, but it does create a mess (no permanent paint, I just dont like the poweder all over my shelves where it is hard to clean up)

Here is a picture of the set-up I did this weekend to paint some cabinets. It took one $10 roll of plastic sheeting, and about 45 minutes to tack it to the cieling using 1/4" staples and scrap strips of wood


img

Re: paint booth question

#14

Re: Fans

pecker

>I've been thinking you could rig a cheap explosion proof exhaust, using a small portable dust collector. The back wall of your "booth" could have something like a downdraft table mounted vertically. Just a piece of pegboard with a framed box and a 4" port on it. Place filter over the front of the pegboard, and put the collector outside the shop area.

For a hobbyist level workshop it should suffice...at least as far as getting the fumes out. It may not collect the overspray that well, as you could only generate a couple hundred cfm's of air.


img

Re: paint booth question

#15

Don't Bet On It

Mark Mandell - Gone Round In Jersey

>True explosion-proof units are made from bronze alloys, special bearings and designs, and are often belt-driven with all electrical components well outside the vapor stream. A DC blower with a steel impeller running in a steel enclosure is any BUT explosion proof. You're better off [but NOT COMPLETELY SAFE!] with a plastic fan in a box for $20