General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
by Bill Tindall, E.TN. 7/3/11, 4:25 PM
2 Replies · 15 ViewsLast post 7/6/11, 5:02 PM by Randy Gleckler -
Pressure Treated versus Salt Treated
by David Yoho 7/6/11, 9:03 AM
5 Replies · 171 ViewsLast post 7/6/11, 1:46 PM by Michael Wilkins -
by Marty 7/5/11, 1:29 PM
9 Replies · 16 ViewsLast post 7/6/11, 12:55 PM by Marty -
Need help with plastic laminate/contact cement
by Barry Irby 7/5/11, 11:07 PM
3 Replies · 18 ViewsLast post 7/6/11, 3:29 AM by Jesper, Denmark -
Directly comparing Seal Coat to Deft....
by Barry Irby 7/4/11, 10:34 PM
11 Replies · 24 ViewsLast post 7/6/11, 1:31 AM by FredD -
by Andy Lincoln 7/5/11, 7:11 PM
1 Reply · 21 ViewsLast post 7/5/11, 10:56 PM by Philip Duffy -
by Dan Turner 7/5/11, 8:57 PM
2 Replies · 16 ViewsLast post 7/5/11, 10:21 PM by Mark Mandell - Gone Round In Jersey -
Evaluation titanium nitride coated plane blade 2
by Bill Tindall, E.TN. 7/5/11, 7:46 PM
0 Replies · 19 ViewsLast post 7/5/11, 7:46 PM by Bill Tindall, E.TN. -
by Larry in NW OHIO 7/5/11, 1:53 PM
4 Replies · 22 ViewsLast post 7/5/11, 7:30 PM by Larry in NW OHIO -
by Barry Irby 7/3/11, 11:34 PM
17 Replies · 45 ViewsLast post 7/5/11, 6:07 PM by AZ -
Rabbeted dadoes... joint strength?
by JL 7/5/11, 12:46 PM
4 Replies · 20 ViewsLast post 7/5/11, 5:53 PM by AZ -
Moisture Meter at Lowe's *LINK*
by Andy Lincoln 6/30/11, 12:07 AM
11 Replies · 21 ViewsLast post 7/5/11, 4:20 PM by Kevin -
I heard that K-Mart bought Sear's for Billions?
by del schisler 7/5/11, 12:32 PM
3 Replies · 22 ViewsLast post 7/5/11, 3:13 PM by Jerry Nicholson -
by Stephen Shepherd 7/5/11, 1:45 PM
0 Replies · 17 ViewsLast post 7/5/11, 1:45 PM by Stephen Shepherd -
Rechargeable Battery questions Again
by Barry Irby 7/4/11, 11:43 AM
12 Replies · 35 ViewsLast post 7/5/11, 11:33 AM by Bill Tindall, E.TN. -
by Philip Duffy 6/30/11, 8:15 PM
13 Replies · 56 ViewsLast post 7/4/11, 9:24 PM by Barry Irby -
Chicken or egg. Epoxy and Oil finish
by Alan Young 7/4/11, 3:53 PM
5 Replies · 16 ViewsLast post 7/4/11, 7:29 PM by Clint Searl -
by steve mackay 7/3/11, 8:28 PM
10 Replies · 17 ViewsLast post 7/4/11, 5:16 PM by paul in AZ -
by doug f 7/3/11, 11:35 PM
3 Replies · 17 ViewsLast post 7/4/11, 12:27 PM by Jim Pugh -
Questions on using air dried wood????
by Barry Irby 7/3/11, 1:27 AM
10 Replies · 26 ViewsLast post 7/4/11, 3:13 AM by Dick Coers -
OT - Decks - Western Red Cedar
by Ray - Middletown, In 7/1/11, 12:06 AM
16 Replies · 46 ViewsLast post 7/4/11, 12:34 AM by Ray - Middletown, In -
by Jerome Mills 7/3/11, 5:25 PM
6 Replies · 24 ViewsLast post 7/3/11, 11:24 PM by del schisler -
by Doug Ridley 7/3/11, 2:44 PM
7 Replies · 21 ViewsLast post 7/3/11, 8:17 PM by George -
Custom Hinge and Pre Cat Lacquer.
by Greg Muller 7/1/11, 8:04 PM
10 Replies · 26 ViewsLast post 7/3/11, 7:18 PM by FredD -
by Thomas Skaggs 6/30/11, 7:42 PM
13 Replies · 23 ViewsLast post 7/3/11, 3:02 PM by Kneale Brownson -
Thoughts on finishing cherry and spalted maple
by Stephen Kirk 7/1/11, 2:35 PM
13 Replies · 49 ViewsLast post 7/3/11, 2:36 PM by Clint Searl -
by Jim DeLaney, Austintown, Ohio 6/30/11, 11:56 PM
2 Replies · 10 ViewsLast post 7/3/11, 11:36 AM by Jim DeLaney, Austintown, Ohio -
by Stuart Johnson 7/2/11, 6:53 PM
6 Replies · 12 ViewsLast post 7/3/11, 4:27 AM by Tom Dunlap -
Sears dovetail fixture and unknown bit
by Gary Smyth 6/30/11, 6:45 PM
5 Replies · 38 ViewsLast post 7/2/11, 3:44 PM by Gary Smyth -
by Rob Hix - King George, VA 7/1/11, 7:17 PM
3 Replies · 12 ViewsLast post 7/2/11, 1:56 PM by Howard Acheson



