Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

Thoughts on finishing cherry and spalted maple

Posts

Thoughts on finishing cherry and spalted maple

#1

Thoughts on finishing cherry and spalted maple

Stephen Kirk

I'm closing in on completing a pair of chairs made from cherry and spalted maple. I might normally leave these woods natural, but the maple seems to need something. I know that most stains will simply cover up the wonderful grain and likely blotch.

I can spray (recently grabbed the Earlex 5500) and I'm thinking of adding some color to a topcoat. These chairs have lots of slats and such so I think spraying is the way to go.

Btw - I only had the chance to test out the Earlex on some scrap using un-thinned General water based poly and the wrong sized needle and it sprayed fine. Wow, I've been missing a lot not having a sprayer. Can't wait to try shellac and lacquers.

Re: Thoughts on finishing cherry and spalted maple

#2

Re: Thoughts on finishing cherry and spalted maple

paul in AZ

Try some boiled linseed on the maple. I use it almost routinely on cherry to accelerate the color change and have found that it gives spalted maple a warm glow.

Re: Thoughts on finishing cherry and spalted maple

#3

Clint Searl

Re: Thoughts on finishing cherry and spalted maple

Clint Searl

Spalted maple looks pretty good under straight NC lacquer; no stain, no BLO. Likewise cherry.

Clint


Re: Thoughts on finishing cherry and spalted maple

#4

Clint Searl

And NO vinyl "sealer"

Clint Searl

Re: Thoughts on finishing cherry and spalted maple

#5

Re: Thoughts on finishing cherry and spalted maple

Jesse Cloud

Good job managing the grain on those maple drawers, they flow together beautifully. And +1 on plain lacquer.

Re: Thoughts on finishing cherry and spalted maple

#6

Careful

Mark Mandell - Gone Round In Jersey

Of tinted finish as it's very each to get blotching and heavy spots, even when spraying. In fact, I suggest your avoid it entirely until you get evry much better with your spray gun. I will tint a shellac coat as a tonning/glazing application, but with shellac only so that if I mess up, it all comes off with an alcohol rub-down.

Speaking of shellac, you can use one of the darker shades of dewaxed shellac, Garnet or Dark Garnet, as both a sealer and toner that's especially useful on splated wood. Two applications of fresh, 1 lb cut is usually sufficient to both even out absorption and "pop" your grain as well as a coat of oil, but with the benefit of being dry and recoatable in an hour or so.

Re: Thoughts on finishing cherry and spalted maple

#7

Jim DeLaney, Austintown, Ohio

Re: Thoughts on finishing cherry and spalted maple

Jim DeLaney, Austintown, Ohio

What Clint said, or if you're into water-based, a pre-cat WB lacquer with just a touch of amber tint added.

BTW, isn't "water-based lacquer" an oxymoron?

Re: Thoughts on finishing cherry and spalted maple

#8

+2 on lacquer and no stain of any kind

del schisler

_

Re: Thoughts on finishing cherry and spalted maple

#9

Re: Careful

FredD

In addition to what Mark suggests , tinting a finish coat with dye ,has the same effect as Paint , each pass with the gun will be darker .

FredD

Re: Thoughts on finishing cherry and spalted maple

#10

Re: Thoughts on finishing cherry and spalted maple

Mark Valsi

Wow, I love that chest. The hardware looks like some of the st uff I have used. Very nice in all aspects. how bout some more pics ??

Re: Thoughts on finishing cherry and spalted maple

#11

Clint Searl

Per your request

Clint Searl

The frames are dyed red oak; top, sides, and back panels are T&G bamboo strip flooring; spalted maple above, spalted beech below; straight NC lacquer finish.


And the blanket chest. The panels are veneered fabric and patinated metalic paint under an NC top coat.


Re: Thoughts on finishing cherry and spalted maple

#12

Re: Per your request

Mark Valsi

ICHI BAN, indeed !!

great piece ! Wow !

Re: Thoughts on finishing cherry and spalted maple

#13

that is what I was thinking

Bill Tindall

If anything, oil it, allow to dry many days to cure oil and then spray with nitrocellulose lacquer. Or, just spray with lacquer.

I think there is great peril in trying to stain as it will take a lot of experience to get it uniform on something as complicated as a chair with all its parts and surfaces. By all means practice on something first.

Re: Thoughts on finishing cherry and spalted maple

#14

Clint Searl

Agree

Clint Searl

This sounds like an instance where I'd consider a wipe-on poly finish.

Clint