Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Custom Hinge and Pre Cat Lacquer.

Posts

Custom Hinge and Pre Cat Lacquer.

#1

Custom Hinge and Pre Cat Lacquer.

Greg Muller

I have two completely different questions. I need to have a custom size hinge made for a large Library stand. I need the hinge in either brass or brush nickle but cannot find anyone to make it. Does any one know where I can get one made up.

Went to Sherwin williams looking for lacquer and the only one that had is a pre cat lacquer. I took it because I could not find any other lacquer other then Minwax and I am looking to spray for this project. I have never used precat lacquer and am looking for any tips or tricks or warnings I should know about. I will be useing a Earlex 5500 to spray. Thanks.

Re: Custom Hinge and Pre Cat Lacquer.

#2

Re: Custom Hinge and Pre Cat Lacquer.

Dick Coers

Precat sprays and acts just like traditional lacquer. Don't be fooled by their claims of water resistance. My kitchen cabinets don't look good by the dishwasher and stove. It is a little better than traditional, but it does not meet the sale pitch.

Re: Custom Hinge and Pre Cat Lacquer.

#3

Re: Custom Hinge and Pre Cat Lacquer. *LINK*

del schisler

I use pre cat lacquer made by M.L.CAMPBEL . I use a sanding sealer than the simi gloss. M.L.Campbel is own by shermin william's but they make their own produt's . I doubt that they are any different. It spray's like any other. You can get run's like any other if sprayed to heavy. As far as the hinge i didn't see a size for the hinge? maybe i missed it. Try whitechapel here is the link


http://www.whitechapel-ltd.com/category/hng.html

Re: Custom Hinge and Pre Cat Lacquer.

#4

Re: Custom Hinge and Pre Cat Lacquer.

John Veerkamp

If you're looking for continuous (piano) type hinge, They can be bought in standard lengths at better hardware stores and even the big boxes. Cut them to length with a hacksaw.

Re: Custom Hinge and Pre Cat Lacquer.

#5

Re: Custom Hinge and Pre Cat Lacquer.

FredD

Del has it right for using Precat Lacquer, it is tougher then NC Lacquer and recommended for Moisture prone areas like Kitchens and baths.

I have used it for the last seven or eight years over the recommended Vinyl Sanding Sealer without a hitch , but I spray a lot of finish and that experience gives one a leg up over now and then operations.

Here is Campbells site and their recommendations.

www.mlcampbell.com/products/categories/clear_sealers

FredD

Re: Custom Hinge and Pre Cat Lacquer.

#6

Clint Searl

Re: Custom Hinge and Pre Cat Lacquer.

Clint Searl

I suggest that "now and then operations" are what the WC audience is all about. One man professional and hobbyist shops are making furniture that will reside in a typical home environment where it won't be exposed to harsh treatment. Also, the makers here aren't doing production finishing, and a can of finish may sit on the shelf for months or more than a year. It makes sense then to find and settle on a finish that has certain attributes. In my 35+ ears of "now and then operations" I have chosen to stick with one-part solvent NC and CAB lacquers because:

1. The look - warm amber or water white and multiple sheens

2. Durability - skateboarders aren't allowed on my furniture and flooding is the least of my worries

3. They're self sealing

4. Easy to apply: flexible in thinning, not time constrained, and overcoats burn in

5. Easy to rub out

6. Pot life is not an issue and multi-year shelf life

7. They can be tinted and enhanced with pearls, micas, metal powders, etc

8. They can be used over water, NGR, and oil stains and over milk paints and pigmented latex/acrylics

9. Wide availability - I go with S-W products for availability and consistance

Clint

Re: Custom Hinge and Pre Cat Lacquer.

#7

Re: Custom Hinge and Pre Cat Lacquer.

FredD

I agree Clint , nothing new about your list , that's why anybody would use Lacquer.

FredD

Re: Custom Hinge and Pre Cat Lacquer.

#8

Re: Custom Hinge and Pre Cat Lacquer.

Greg Muller

I went to SW looking for a NC lacquer and ordered what I thought was a one part NC lacquer. When I went to pick it up it turned out to be the pre cat. When I told the clerk I was looking for a NC lacquer he said this was the only one he could get so I took it. I am tempted to bring it back but if it is similiar to the one part NC lacquer I will try to use it.

Re: Custom Hinge and Pre Cat Lacquer.

#9

Re: Custom Hinge and Pre Cat Lacquer.

FredD

Sounds like a typical S-W shopping experience to me John.

The PRe-Cat lacquer will work just fine and give you a tougher finish then NC.

To get the full advantage of a Catalyzed finish like that , you really should follow the directions on the can and when you clean the equipment ,pay attention to getting it clean.

FredD

Re: Custom Hinge and Pre Cat Lacquer.

#10

Clint Searl

Re: Custom Hinge and Pre Cat Lacquer.

Clint Searl

Fred, how do you clean a gun in which the Pre Cat has cured?

Clint

Re: Custom Hinge and Pre Cat Lacquer.

#11

Re: Custom Hinge and Pre Cat Lacquer.

FredD

I have never that problem Clint though i know a couple of Painters that did.

If the pre-cat dries in the gun , it s necessary to dissemble the gun , soak in something as strong as MEK.

You may also ruin the gaskets , so they need replaced, small cost , but time consuming.

When I am spraying Lacquer and Sealer , after spraying the sealer, instead of cleaning the gun , I hang it in a coffee can of Lacquer thner, so nothing dries.

After the lacquer is sprayed I run nearly a Coffee can of thinner thought the gun and then wrap the gun in a clean cotton cloth so some thinner stays in the gun.

Occasionally I lube the inner gasket with the stuff Graco provides.

This has never failed me .

FredD