Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Directly comparing Seal Coat to Deft....

Posts

Directly comparing Seal Coat to Deft....

#1

Directly comparing Seal Coat to Deft....

Barry Irby

I finally got my old spray gun working again. (Bill would day its an antique, actually older than my battery powered drills.) I was trying to refurbish same beat up kitchen cabinets by wiping them with stain and then applying a coat of Deft Lacquer. I got what I think is Fish Eye. Something was pushing the lacquer away, leaving spots that looked like someone dropped a stone in the water and then froze the ripple. I had the shop/garage door open for ventilation and the mosquitoes were giving me a fit. I tried using Zinsser SealCoat Shellac as a sealer to cure the fish eye or whatever it was. What I learned is that Deft will kill a mosquito in mid air if you drench him with the spray gun. Sealcoat does not seem to be nearly as deadly on the them, but they sure look good, very shiny.

Re: Directly comparing Seal Coat to Deft....

#2

Re: Directly comparing Seal Coat to Deft....

Ken Oakley-Sunny St. Cloud, Fla

Did you thin the Deft properly? Did you spray a bug repellent? Either one could be the cause.

Re: Directly comparing Seal Coat to Deft....

#3

Re: Directly comparing Seal Coat to Deft....

Dick Coers

Deft is a pretty poor finish for a kitchen cabinet. It has low water and heat resistance.

Re: Directly comparing Seal Coat to Deft....

#4

Re: Directly comparing Seal Coat to Deft....

Barry Irby

I wanted to use something that is compatible with the old finish on the cabinets. I assumed they had lacquer from 1977. I went to Sherwin Williams. They had a water based product. Tried two other paint stores. Ended up taking the easy way out and used Deft that was available at Lowes.

What would be your choice and where would you get it?

This is a house I bought at foreclosure and I probably should have replaced the cabinets, but I am trying to keep costs under control. It will be a rental.

Re: Directly comparing Seal Coat to Deft....

#5

Re: Directly comparing Seal Coat to Deft....

FredD

If you have Fish eye caused by Silicone contamination which interferes with the surface tension of the finish , you neet to cleanit off with Paint thinner.

The Fish eye will appear regardless of how many or different coats of finish you use , until it is off of the wood.

The contamination is often caused by using Furniture polish that contains it.

FredD

Re: Directly comparing Seal Coat to Deft....

#6

Re: Directly comparing Seal Coat to Deft....

Barry Irby

Fred, I sprayed one drawer front and had this problem. I don't actually know what it was. there were irregular circles where the surface looked thin in the center and sort of mounded up around the perimeter. By the time I found this, I had gently scrapped the crud off these cabinets, lightly sanded them and wiped on a coat of Minwax special Walnut stain to cover the scratches and let it dry. I have never done this before and it did not occur to me to wipe them down with thinner.

So, I coated the rest of the doors with SealCoat. Other wise I would have had to wash off the stain coat. That seemed to have worked fine. They look OK with no Fish Eye Effect. After I did these, I did wipe down any other parts I worked on.

This is and exercise in achieving "Perfect". When we are working on something in front of a client and get the work to the a satisfactory level we say "perfect". They don't respond well to "that's good enough", but they like to hear Perfect. So perfect is that level of perfection necessary for this job. So, these cabinets are perfect. 30 years old, beat up and battered, but salvaged and good enough for another round. They will not lower the rent and will function far into the future.

Re: Directly comparing Seal Coat to Deft....

#7

Ellis Walentine

My take on this...

Ellis Walentine

.... is that you didn't let your stain dry well enough to coat it with lacquer. Seal Coat is a barrier coat that is compatible over just about everything.

Stains are deceptive, and that goes for all types that I've used. I even had trouble once topcoating over a NGR stain (Constantine's or Behlen, or Star, not sure which). They seem dry, but they aren't dry enough.

Ellis

Re: Directly comparing Seal Coat to Deft....

#8

Re: My take on this...

Barry Irby

You may be correct, but what I did was wipe on stain and set them out int the driveway in the sun and let them cook all day. Then I brought them in the next day and sprayed them. So, they were in the sun all day and then over night. They seemed dry, but you are correct, that might not have been enough. I have three more panels to do and they have been drying even longer.

I have a small shop and there was no way to keep this many pieces indoors. I was worried about insects getting into the finish, but that did not turn out to be a problem. OTOH a bird left me a huge surprise on one of them. Good accuracy and amazing quantity. Who knew a bird could hold so much and still fly?

Re: Directly comparing Seal Coat to Deft....

#9

Steve Strickland

Re: My take on this...

Steve Strickland

A lot of finishing products use solvents that will outgas after the finish is "dry".

There's a way to tell how long outgassing takes to complete. Finish 4 or 5 small samples. Each day tight seal one sample with saran food wrap. Check the samples as you go along. The plastic wrap will trap the gasses and stain the finish where it's in contact with the wrap. I find that the day 4 sample will not stain with the stuff I use so I figure that's how long it takes for the outgassing to stop. Sometimes the day 3 sample is good but why take a chance.

I don't really know what's going on with your situation but it seems possible that you might be trapping outgasses with the overcoat. If so, the solution is to wait until the outgassing terminates before applying the overcoat. If the saran wrap test is negative then you probably have some other problem.

Please let us know!

Re: Directly comparing Seal Coat to Deft....

#10

Re: Directly comparing Seal Coat to Deft....

FredD

The fish eye I have encountered always looked more like crater on the moon then a fish eye and the two time it happened , was on a drawer fronts

About stain drying , I have never had a problem with it drying enough to finish coat over night , you should have the same results less something is retarding the drying time like cold weather .

FredD

Re: Directly comparing Seal Coat to Deft....

#11

If this is cold weather....

Barry Irby

I will die when summer really hits here.

Re: Directly comparing Seal Coat to Deft....

#12

Re: Directly comparing Seal Coat to Deft....

FredD

I assumed you would know the difference :D

FredD