Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

General Woodworking

Cross-cutting topics, techniques, and questions that don’t fit a specialty.

Topic list

  1. Military Sword and Scabbard Cases

    by Alan Young 2/18/24, 6:17 PM

    2 Replies · 622 Views
    Last post 2/18/24, 9:46 PM by Alan Young
  2. One Of Those Mornings...

    by John McGaw (Bodger) 2/17/24, 4:05 PM

    7 Replies · 591 Views
    Last post 2/18/24, 7:59 PM by Barry Irby
  3. Key cabinet

    by Svante Nilsson 2/15/24, 9:49 AM

    3 Replies · 589 Views
    Last post 2/17/24, 7:27 PM by Alan Young
  4. Poplar grain showing through paint

    by Mike L 1/13/24, 8:50 PM

    8 Replies · 2,286 Views
    Last post 2/17/24, 5:58 PM by Henry (Raleigh NC)
  5. Hard Maple counter top finish

    by Mike L 2/13/24, 4:50 PM

    4 Replies · 449 Views
    Last post 2/16/24, 4:16 PM by Ed morini
  6. Plane Wellness

    by admin 2/6/24, 4:40 PM

    15 Replies · 1,429 Views
    Last post 2/13/24, 10:59 PM by Peter Martin
  7. Jointing and planing questions

    by Joe Fleming 2/2/24, 4:19 PM

    11 Replies · 1,227 Views
    Last post 2/13/24, 6:20 PM by Gary Focht
  8. Badger Pond

    by admin 1/29/24, 4:09 AM

    15 Replies · 1,439 Views
    Last post 2/12/24, 8:14 PM by John b
  9. Shop cabinet done. I learned a lot

    by Mike L 2/12/24, 1:51 AM

    3 Replies · 440 Views
    Last post 2/12/24, 5:43 PM by Joe Fleming
  10. Back again

    by David Smith 1/22/24, 3:48 AM

    5 Replies · 750 Views
    Last post 2/11/24, 10:04 AM by Moses Yoder
  11. Bow front vanity? Resources for build?

    by Henry (Raleigh NC) 2/4/24, 8:06 PM

    5 Replies · 1,009 Views
    Last post 2/6/24, 10:24 AM by Ellis Walentine
  12. OT: Where do you think new woodworkers are going? 2

    by david weaver 5/16/19, 4:02 PM

    28 Replies · 2,106 Views
    Last post 2/3/24, 12:43 PM by admin
  13. Designing a dining carver chair 2

    by Derek Cohen (in Perth, Australia) 12/30/23, 7:02 AM

    37 Replies · 4,429 Views
    Last post 2/1/24, 1:06 PM by admin
  14. Welcome to our second quarter-century!

    by Ellis Walentine 1/8/24, 4:46 AM

    4 Replies · 655 Views
    Last post 1/29/24, 12:33 PM by Ellis Walentine
  15. 0 Replies · 248 Views
    Last post 1/25/24, 1:29 PM by jd
  16. Question about Smart TV's

    by Ralph Lipeles 12/14/23, 8:51 PM

    17 Replies · 1,128 Views
    Last post 1/22/24, 2:53 PM by Ralph Lipeles
  17. Claro walnut humidor

    by Jim in Burlington Ont. 1/13/24, 6:04 PM

    6 Replies · 595 Views
    Last post 1/21/24, 10:53 PM by Virgil Johnson
  18. 4 Replies · 683 Views
    Last post 1/15/24, 11:41 PM by Steve Elliott
  19. Bandsaw resaw fence

    by Derek Cohen (in Perth, Australia) 12/18/23, 9:04 AM

    11 Replies · 1,204 Views
    Last post 1/13/24, 5:36 PM by Jim in Burlington
  20. 2 Replies · 459 Views
    Last post 1/11/24, 6:19 PM by Bruce McCrory
  21. Piano gloss black?

    by Henry (Raleigh NC) 1/4/24, 9:27 PM

    6 Replies · 711 Views
    Last post 1/8/24, 10:14 PM by Henry (Raleigh NC)
  22. Dammit Petrer

    by Barry Irby 1/2/24, 2:05 PM

    7 Replies · 713 Views
    Last post 1/6/24, 9:26 AM by admin
  23. Mission style desk/table

    by Andy Lincoln 12/31/23, 10:19 PM

    1 Reply · 320 Views
    Last post 1/1/24, 5:34 AM by Dale Stansbery
  24. Completed Gifts (just in time) - Candle Stand center-pieces.

    by Henry (Raleigh NC) 12/30/23, 9:27 PM

    0 Replies · 393 Views
    Last post 12/30/23, 9:27 PM by Henry (Raleigh NC)
  25. Biggest influence

    by admin 12/16/23, 2:00 PM

    22 Replies · 1,916 Views
    Last post 12/30/23, 5:52 PM by Charlie
  26. Fine Woodworking Magazine

    by John Pappas 12/21/23, 6:54 PM

    8 Replies · 1,097 Views
    Last post 12/30/23, 5:49 PM by Charlie
  27. Shaping elliptical, curved chair legs

    by Derek Cohen (in Perth, Australia) 12/27/23, 5:44 AM

    3 Replies · 826 Views
    Last post 12/30/23, 5:45 PM by Charlie
  28. Big Dining Table at Dinner Time

    by Alan Young 12/29/23, 9:02 PM

    3 Replies · 506 Views
    Last post 12/30/23, 3:37 PM by Charlie