General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
Stephen Shepherd back in the Chat Room
by Ellis Walentine 3/27/07, 7:41 PM
2 Replies · 53 ViewsLast post 3/27/07, 9:01 PM by Alan Young -
Large old bandsaw - ID needed...
by John Aniano - in NJ... 3/27/07, 2:34 AM
6 Replies · 79 ViewsLast post 3/27/07, 6:06 PM by Mark Goodall - ATL - tooljunkie -
JET Days at Woodcraft coming up
by Pete LaBelle 3/27/07, 5:07 PM
0 Replies · 67 ViewsLast post 3/27/07, 5:07 PM by Pete LaBelle -
Bandsaw riser block - - drawbacks ?
by Pete LaBelle 3/26/07, 1:43 PM
13 Replies · 191 ViewsLast post 3/27/07, 4:56 PM by Pete LaBelle -
by Dustmaker Mike 3/26/07, 10:19 PM
2 Replies · 57 ViewsLast post 3/27/07, 2:36 PM by Hank Knight from SC -
by Barry Irby 3/27/07, 1:16 PM
2 Replies · 58 ViewsLast post 3/27/07, 1:26 PM by John in New Mexico -
Kitchen Countertop Material choices
by Dan Manturi 3/24/07, 11:26 AM
20 Replies · 126 ViewsLast post 3/27/07, 12:37 PM by Jim Dillon -
by Jim Toews - Walla Walla, WA 3/26/07, 2:38 PM
4 Replies · 57 ViewsLast post 3/27/07, 6:12 AM by Carol from AZ -
by Brint in Atlanta 3/25/07, 3:18 AM
8 Replies · 116 ViewsLast post 3/27/07, 2:40 AM by Brint in Atlanta -
by Gary Evans Tallassee, TN 3/25/07, 4:05 PM
3 Replies · 64 ViewsLast post 3/27/07, 2:06 AM by Ellis Walentine -
WC Weekend Accomplishments.....
by Dennis E. Peacock 3/26/07, 2:21 PM
11 Replies · 81 ViewsLast post 3/27/07, 1:52 AM by Keith Newton -
Looking for a riser block. Rockwell Model 14
by MaxM 3/26/07, 12:46 PM
4 Replies · 57 ViewsLast post 3/27/07, 12:20 AM by Paul Waddle -
by s.mackay@worldnet.att.net 3/26/07, 10:42 PM
0 Replies · 60 ViewsLast post 3/26/07, 10:42 PM by s.mackay@worldnet.att.net -
System is running slow this morning.
by Tim Caley - North Little Rock, AR 3/26/07, 2:39 PM
4 Replies · 61 ViewsLast post 3/26/07, 9:57 PM by Tim Caley - North Little Rock, AR -
by Keith Newton 3/26/07, 9:54 PM
0 Replies · 53 ViewsLast post 3/26/07, 9:54 PM by Keith Newton -
by Paul Regan 3/20/07, 4:42 PM
18 Replies · 111 ViewsLast post 3/26/07, 6:25 PM by Ron Goldman -
OT Metal Detectors-not for nails in wood
by Larry Shapiro, Fairfax, Va 3/23/07, 7:36 PM
8 Replies · 187 ViewsLast post 3/26/07, 5:23 PM by Larry Shapiro, Fairfax, Va -
Drywall Again ....... Corners This Time
by Joe Burke 3/26/07, 12:46 PM
5 Replies · 70 ViewsLast post 3/26/07, 4:46 PM by Ray Thompson - Middletown,IN -
Dumb Question--- band saw blade lube?
by Dave Morris 3/24/07, 3:46 PM
10 Replies · 92 ViewsLast post 3/26/07, 3:55 PM by Keith Newton -
by Peter Galbert 3/25/07, 4:03 PM
3 Replies · 58 ViewsLast post 3/26/07, 2:52 PM by Curly Smith -
Hey Ellis ...... try this again
by Joe Burke 3/26/07, 12:33 PM
1 Reply · 53 ViewsLast post 3/26/07, 2:36 PM by Ellis Walentine -
by Jim Jacomb 3/26/07, 2:41 AM
2 Replies · 73 ViewsLast post 3/26/07, 1:37 PM by Dominic Greco in Richboro PA -
by Joe 3/25/07, 12:25 PM
17 Replies · 77 ViewsLast post 3/26/07, 11:55 AM by Joe -
by bill tindal, E.TN 3/25/07, 4:11 PM
3 Replies · 68 ViewsLast post 3/26/07, 11:20 AM by Mike in Paradise -
Jet 14" BS... table fence hole location?
by Dave Morris 3/25/07, 10:19 PM
4 Replies · 158 ViewsLast post 3/26/07, 5:02 AM by Al Crandall (N.E. of Indy) -
Here is another picture of the log in action
by Ron in Drums PA 3/25/07, 2:47 PM
2 Replies · 61 ViewsLast post 3/26/07, 4:33 AM by Fred West in West Chester, PA -
Oral B should make a cordless Drill
by Mike in Paradise 3/25/07, 10:18 AM
6 Replies · 51 ViewsLast post 3/26/07, 3:44 AM by DB -
by John in MD 3/25/07, 6:53 PM
11 Replies · 96 ViewsLast post 3/26/07, 2:53 AM by Rusty -
Re: How do you cut your sheet goods?
by John Smith 3/16/07, 3:50 AM
0 Replies · 0 ViewsLast post 3/26/07, 2:25 AM by NickB -
How do you cut your sheet goods? 2
by Lee Beeden 2/1/07, 4:36 PM
36 Replies · 265 ViewsLast post 3/26/07, 2:25 AM by NickB



