General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
by Joe 1/3/11, 1:55 PM
3 Replies · 42 ViewsLast post 1/3/11, 6:08 PM by Bill Tindall, E.TN. -
by Bartstar 1/2/11, 4:02 PM
4 Replies · 49 ViewsLast post 1/3/11, 4:43 AM by Ellis Walentine -
by Phil Joines 1/3/11, 1:40 AM
0 Replies · 26 ViewsLast post 1/3/11, 1:40 AM by Phil Joines -
by Dick H. 12/29/10, 5:59 PM
8 Replies · 26 ViewsLast post 1/2/11, 11:25 PM by Dale Lenz -
by Bill Tindall, E.TN. 1/1/11, 1:36 PM
18 Replies · 35 ViewsLast post 1/2/11, 8:44 PM by Bill Houghton -
by Ken Oakley-Sunny St. Cloud, Fla. 1/1/11, 12:22 AM
12 Replies · 19 ViewsLast post 1/2/11, 8:42 AM by Ken Oakley-Sunny St. Cloud, Fla -
Quetion: How to make a 'Square' cutout
by Bob S 12/30/10, 5:19 PM
14 Replies · 62 ViewsLast post 1/2/11, 3:26 AM by AZ -
by GDeavers 1/1/11, 6:47 AM
1 Reply · 11 ViewsLast post 1/1/11, 9:49 PM by Don Orr -
by Nelson 12/30/10, 5:08 AM
8 Replies · 41 ViewsLast post 1/1/11, 9:17 PM by morris -
by Bill Tindall, E.TN. 1/1/11, 1:43 PM
4 Replies · 24 ViewsLast post 1/1/11, 4:32 PM by Ray - Middletown, IN -
by Ken Oakley-Sunny St. Cloud, Fla. 12/30/10, 12:15 AM
5 Replies · 32 ViewsLast post 1/1/11, 3:54 PM by jrecord -
by Henry Higginbotham 12/29/10, 8:06 PM
6 Replies · 16 ViewsLast post 1/1/11, 1:16 PM by Lee Schierer McKean, PA -
Happy Holidays and New Year Everybody *LINK*
by Hikmet C. Sakman 12/26/10, 8:31 PM
8 Replies · 19 ViewsLast post 1/1/11, 1:04 PM by Lee Schierer McKean, PA -
by McKay 12/31/10, 10:35 PM
2 Replies · 13 ViewsLast post 1/1/11, 6:04 AM by Scott in Montana -
by Doug Reynolds in Seattle 12/30/10, 6:32 PM
8 Replies · 29 ViewsLast post 1/1/11, 1:14 AM by FredD -
by Stuart Hough 12/31/10, 1:40 PM
5 Replies · 14 ViewsLast post 1/1/11, 12:29 AM by Don Orr -
by Robert R. Clough 12/29/10, 2:54 PM
19 Replies · 25 ViewsLast post 12/31/10, 6:30 PM by Gary Camp Bend, Oregon -
by Ken Oakley-Sunny St. Cloud, Fla 12/30/10, 6:48 PM
8 Replies · 21 ViewsLast post 12/31/10, 5:54 PM by Clint Searl -
by Bartstar 12/30/10, 8:29 PM
2 Replies · 60 ViewsLast post 12/31/10, 4:49 PM by Bartstar -
Question on fitting a solid bottom box in a toybox
by Ken Bellock (Houston, TX) 12/30/10, 4:14 PM
8 Replies · 63 ViewsLast post 12/31/10, 3:57 PM by Jim Dillon -
by woodenleg 12/29/10, 6:12 AM
4 Replies · 26 ViewsLast post 12/31/10, 4:33 AM by jared -
by Rick Haverstock 12/30/10, 3:13 AM
9 Replies · 35 ViewsLast post 12/31/10, 4:17 AM by Robby Wright in San Marcos, CA -
Drawer Faces: How much overlap?
by Ed 12/28/10, 2:55 AM
6 Replies · 89 ViewsLast post 12/30/10, 8:25 PM by Bartstar -
by Bill Tindall, E.TN. 12/27/10, 3:18 PM
13 Replies · 37 ViewsLast post 12/30/10, 1:11 PM by John in NM -
Design question - grain orientation
by JL 12/29/10, 11:48 AM
7 Replies · 38 ViewsLast post 12/30/10, 1:07 PM by Jim Runchey -
OT - condensation on sheet foam insulation
by Bill Houghton 12/29/10, 7:27 AM
10 Replies · 92 ViewsLast post 12/30/10, 5:24 AM by Jesper, Denmark -
by Carl Cooksey 12/29/10, 9:47 PM
0 Replies · 15 ViewsLast post 12/29/10, 9:47 PM by Carl Cooksey -
by Keith Newton----Little Rock, Arkansas 12/29/10, 5:03 PM
1 Reply · 59 ViewsLast post 12/29/10, 5:23 PM by Bill Turpin -
by Thomas Norton 12/28/10, 12:41 PM
5 Replies · 24 ViewsLast post 12/29/10, 2:52 PM by Jim DeLaney, Austintown, Ohio -
Flummoxed by annoying posting problem
by Bill Tindall, E.TN. 12/28/10, 7:03 PM
8 Replies · 24 ViewsLast post 12/29/10, 2:28 PM by del schisler



