Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Question on fitting a solid bottom box in a toybox

Posts

Question on fitting a solid bottom box in a toybox

#1

Question on fitting a solid bottom box in a toybox

Ken Bellock (Houston, TX)

I'm building a walnut toy box/blanket chest for my daughter. I'm about ready to glue up the box, and am deciding how to fit the solid bottom to the sides. The bottom panel is 3/4" thick, as are the sides. Should I just cut 3/4" dadoes into the sides for this board to fit in, or is it better to put a rabbet on the panel. From previous boxes I know it is easier to center the panel with a rabbet, but want to make the bottom as strong as possible. I see her jumping in out of this box and want it to be able to withstand as much abuse as possible. What is the ideal depth to sink the panel into the sides for strength as well? Just guessing somewhere between a third and half of the thickness?

I know how to account for movement of the panel, I'm just not sure how to get the strongest possible support for the bottom while allowing the panel to float.

Thanks for any help or tips! :D

Re: Question on fitting a solid bottom box in a toybox

#2

Re: Question on fitting a solid bottom box in a to

Larry in NW OHIO

Ken I would just cut your 3/4 dado and call it good. I think that would the best for strength. Larry

Re: Question on fitting a solid bottom box in a toybox

#3

Re: Question on fitting a solid bottom box in a to

Dave Bair, Eaton Rapids, MI

For extra strength, I'd use screwed-and-glued cleats. They can also be combined with the dado for an added magnitude of tough.

Re: Question on fitting a solid bottom box in a toybox

#4

Re: Question on fitting a solid bottom box in a to

Bill Tindall

Rabbit or "raise panel" to get a 3/8" lip. Set in a 1/4 to 3/8" deep groove. The more shallow the groove the stronger the arrangement. There is no way an adult will break across the grain of a 3/8" board. The weak point is the dado. Captured on four sides even a thin panel is strong.

Re: Question on fitting a solid bottom box in a toybox

#5

Re: Question on fitting a solid bottom box in a to

Joe Mohnike

It sounds as if this is going to be for a child, if so, keep it so that you can repair it at a later date. A groove would require dismanteling the box to repair the bottom, a rabbit would be my choice. If you have the room you could put a center post/leg out of sight to give additional support. Kids and toys can be devistating to a toy box.

Good luck

Joe M.

Re: Question on fitting a solid bottom box in a toybox

#6

Re: Question on fitting a solid bottom box in a to

Barry Irby

Why not put it in a shallow rabbet and then put supports under the bottom that rest on the floor so that the bottom supports the box rather than the other way round?

Re: Question on fitting a solid bottom box in a toybox

#7

Re: Question on fitting a solid bottom box in a to

Jim Dillon

Ken,

Lots of good suggestions by others. I probably would take the approach suggested by Bill and Dave by cutting a rabbet in the floor (to minimize the the side-weakening dado) combined with a ledger around the underside of the floor. You might have to move the floor up a bit to allow room for the ledgers. To make things pretty on the inside, I would add a decorative piece of molding to cover the small gap between the floor and sides.

The downside to this approach, as suggested by Joe, is that future repair is nearly impossible. Although I really don't think a child could break a properly built 3/4 inch floor, a rabbet in the sides with the floor flush to the bottom would allow future repair - as long as the floor was attached with nails or screws.

Another option is to avoid the dado in the side and use the ledgers alone combined with the decorative molding on the inside. If the ledgers were screwed in, future repair would be easy.

Jim

Re: Question on fitting a solid bottom box in a toybox

#8

Re: Question on fitting a solid bottom box in a to

Ken Bellock (Houston, TX)

Thanks all for the suggestions. Here is a rendering of the cad drawing of the box I'm putting together. For scale, it's about 45" long, and about 18" wide. The sides are 15" tall not counting the base or lid. The box is walnut, the base and top will be purpleheart.


Re: Question on fitting a solid bottom box in a toybox

#9

Re: Question on fitting a solid bottom box in a to

Jim Dillon

Ken,

Thanks for the nice schematic. If I wasn't too worried about future repair, I would just set the floor into a rabbet along the bottom edge of the box and either place the entire box/floor into a rabbet cut into your legs, or fasten ledgers to your legs and place the box/floor directly on top of the ledgers.

However, if I could afford taking up a bit of interior space, I might still opt for going with my previous suggestion and then simply set the entire box/floor/ledger into a rabbet cut into the legs. Any future repair would be simple. Hope this makes some sort of sense.

Jim