General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
How would you build a box with 'wainscotting'?
by Henry (Raleigh NC) 7/7/21, 5:10 PM
10 Replies · 98 ViewsLast post 7/8/21, 12:05 AM by Henry (Raleigh NC) -
by Mike L 7/7/21, 12:10 PM
3 Replies · 69 ViewsLast post 7/7/21, 7:26 PM by howard gorman -
by Philip F Duffy 7/5/21, 1:19 PM
4 Replies · 78 ViewsLast post 7/7/21, 2:16 PM by Philip F Duffy -
Any recommendations for router circle-cutting jig
by Howard in Toronto 6/21/21, 10:10 PM
20 Replies · 349 ViewsLast post 7/7/21, 1:45 PM by Henry (Raleigh NC) -
by Howard in Toronto 7/5/21, 6:54 PM
4 Replies · 88 ViewsLast post 7/5/21, 10:13 PM by Howard in Toronto -
by Barry Irby 7/5/21, 1:17 AM
3 Replies · 152 ViewsLast post 7/5/21, 2:37 PM by walta -
by howard gorman 7/4/21, 2:48 PM
7 Replies · 198 ViewsLast post 7/5/21, 10:49 AM by Bill Blasic -
Complementary curve routing video *LINK* 2
by Mark Hennebury 6/19/21, 4:25 PM
39 Replies · 302 ViewsLast post 7/5/21, 2:33 AM by Mark Hennebury -
by Tom Norton 7/3/21, 11:54 AM
9 Replies · 117 ViewsLast post 7/4/21, 11:23 PM by Dave's Not Here -
Rails to Trails Bridge- painting
by Bill Tindall, E.TN. 7/4/21, 7:15 PM
0 Replies · 79 ViewsLast post 7/4/21, 7:15 PM by Bill Tindall, E.TN. -
by Howard Metx 7/2/21, 7:04 PM
2 Replies · 171 ViewsLast post 7/4/21, 6:48 PM by David Weaver -
by howard gorman 7/3/21, 3:25 PM
2 Replies · 113 ViewsLast post 7/4/21, 6:12 PM by kneale brownson -
Rails to Trails bridge progress
by Bill Tindall, E.TN. 7/1/21, 7:56 PM
5 Replies · 72 ViewsLast post 7/4/21, 5:33 PM by Howard in Toronto -
by eliot feldman 6/26/21, 12:38 AM
21 Replies · 401 ViewsLast post 6/30/21, 1:42 PM by Larry Clinton At Frankfort, (Central) Indiana -
Needing new variable speed router?
by Keith L Newton 6/24/21, 2:03 PM
7 Replies · 118 ViewsLast post 6/29/21, 5:52 PM by Howard in Toronto -
by Jerry Gibbs 6/23/21, 9:38 PM
10 Replies · 146 ViewsLast post 6/29/21, 5:52 PM by John K Jordan -
by howard gorman 6/24/21, 10:04 PM
13 Replies · 143 ViewsLast post 6/29/21, 5:44 AM by TomD -
by Buck 6/26/21, 3:24 AM
0 Replies · 96 ViewsLast post 6/26/21, 3:24 AM by Buck -
by JL 6/23/21, 2:27 PM
7 Replies · 106 ViewsLast post 6/26/21, 1:36 AM by A.J. Hamler -
by Barry Irby 6/21/21, 8:22 PM
12 Replies · 133 ViewsLast post 6/25/21, 11:17 PM by Walt -
Pre treating lumber pile for insects
by Barry Irby 6/23/21, 9:34 PM
4 Replies · 96 ViewsLast post 6/25/21, 2:16 AM by Brian Chitwood -
Completely OT Painting Parking lot Lines?
by Barry Irby 6/23/21, 12:14 PM
7 Replies · 84 ViewsLast post 6/24/21, 8:21 PM by Barry Irby -
by eliot feldman 6/18/21, 3:15 PM
7 Replies · 563 ViewsLast post 6/23/21, 4:21 AM by AZ -
Board and Batten siding questions....
by Barry Irby 6/20/21, 10:21 PM
3 Replies · 147 ViewsLast post 6/22/21, 2:28 PM by Mark Salomon -
by Barry Irby 6/20/21, 4:56 PM
9 Replies · 119 ViewsLast post 6/21/21, 11:59 PM by Bruce, a MN Galoot -
by Craig Spacek 6/19/21, 11:17 PM
8 Replies · 102 ViewsLast post 6/21/21, 9:53 PM by Craig Spacek -
OT, how would you cut this plastic fence?
by Tim Greif - West of Chicago 6/16/21, 11:18 PM
19 Replies · 672 ViewsLast post 6/20/21, 12:33 AM by Barry Irby -
How to safely cut cove on the tablesaw
by CJ in MPLS 6/17/21, 11:08 PM
6 Replies · 129 ViewsLast post 6/19/21, 10:47 PM by CJ in MPLS -
Recommendations please: 10 TS blade to replace WW2
by Howard in Toronto 6/16/21, 8:28 PM
7 Replies · 75 ViewsLast post 6/19/21, 3:36 PM by David Weaver -
Speaking or chop saw blades for Aluminum?
by Barry Irby 6/18/21, 8:14 PM
4 Replies · 119 ViewsLast post 6/19/21, 12:08 AM by Andy Lincoln