General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
Mission Finishes on QS White Oak, options?
by Jim in Burlington Ont. 2/6/23, 7:20 PM
5 Replies · 197 ViewsLast post 2/9/23, 2:21 PM by Paul Leuba -
For those with moisture meters...questions...OT?
by Barry Irby 2/5/23, 5:48 PM
16 Replies · 287 ViewsLast post 2/7/23, 1:52 AM by Barry Irby -
by Bill Tindall, E.TN. 2/6/23, 3:52 PM
1 Reply · 119 ViewsLast post 2/6/23, 7:08 PM by Joe Fleming -
Re: The bed and bedhead: final photos
by Jim in Burlington Ont. 2/6/23, 3:26 PM
0 Replies · 125 ViewsLast post 2/6/23, 3:26 PM by Jim in Burlington -
by Mark Mandell 1/31/23, 1:55 PM
13 Replies · 282 ViewsLast post 2/6/23, 3:23 PM by Jim in Burlington -
by Woodie49 1/29/23, 1:21 AM
14 Replies · 281 ViewsLast post 2/5/23, 5:21 PM by AZ -
Re: Extending 6x6 support post
by Don Stephan 1/29/23, 1:12 AM
2 Replies · 143 ViewsLast post 2/5/23, 3:50 PM by Mike L -
by Pat Evans 2/3/23, 11:02 AM
11 Replies · 360 ViewsLast post 2/5/23, 2:56 PM by Bill Tindall E.TN. -
Question for Dick and anybody with a laser?
by Barry Irby 2/2/23, 1:28 PM
12 Replies · 176 ViewsLast post 2/3/23, 10:30 PM by Barry Irby -
Re: Under bench cabinet dry fitted together
by Derek Cohen (in Perth, Australia) 1/29/23, 2:14 AM
1 Reply · 83 ViewsLast post 1/31/23, 12:43 AM by eliot feldman -
Half blind waste removal revisited and a fitting tp
by Bill Tindall, E.TN. 1/30/23, 9:07 PM
2 Replies · 145 ViewsLast post 1/30/23, 11:26 PM by Bill Tindall E.TN. -
Installing an LED under the router
by Bill Tindall, E.TN. 1/29/23, 6:47 PM
5 Replies · 168 ViewsLast post 1/30/23, 3:38 PM by Bill Tindall E.TN. -
by eliot feldman 1/29/23, 1:15 AM
2 Replies · 92 ViewsLast post 1/30/23, 1:31 AM by eliot feldman -
by Steve Elliott 1/29/23, 12:35 AM
13 Replies · 177 ViewsLast post 1/29/23, 6:41 PM by Bill Tindall E.TN. -
Re: Rikon Bandsaw Drive Belt Problem
by Lee Ohmart 1/29/23, 1:30 AM
1 Reply · 143 ViewsLast post 1/29/23, 12:47 PM by Mark Mandell -
by Woodie49 1/29/23, 2:01 AM
1 Reply · 109 ViewsLast post 1/29/23, 4:39 AM by Derek Cohen (in Perth, Australia) -
by eliot feldman 1/29/23, 1:02 AM
0 Replies · 106 ViewsLast post 1/29/23, 1:02 AM by eliot feldman -
by Bill Tindall, E.TN. 1/29/23, 12:59 AM
0 Replies · 121 ViewsLast post 1/29/23, 12:59 AM by Bill Tindall E.TN. -
Re: Under bench cabinet dry fitted together
by eliot feldman 1/29/23, 12:51 AM
0 Replies · 127 ViewsLast post 1/29/23, 12:51 AM by eliot feldman -
Drain from Kitchen sink plugged
by Bill Tindall, E.TN. 9/18/21, 7:49 PM
23 Replies · 270 ViewsLast post 12/18/21, 3:56 PM by Bill Tindall, E.TN. -
Does Anyone Rabbet and Dado Cabinets Anymore?
by John Foster 10/14/21, 2:30 PM
18 Replies · 830 ViewsLast post 10/22/21, 12:53 AM by Clint Searl -
Is 5-thou on a 10" TS blade OK or too high 2 3
by Howard Rosenberg 10/15/21, 1:25 PM
53 Replies · 943 ViewsLast post 10/19/21, 2:06 PM by David Weaver -
by Barry Irby 10/8/21, 10:53 PM
28 Replies · 491 ViewsLast post 10/18/21, 9:38 AM by TomD -
by Bill Tindall, E.TN. 10/8/21, 2:05 PM
10 Replies · 167 ViewsLast post 10/17/21, 4:35 PM by paul in AZ -
by Bill Tindall, E.TN. 10/15/21, 1:09 PM
5 Replies · 184 ViewsLast post 10/16/21, 10:44 AM by Bill Blasic -
by Michael Todrin 10/10/21, 2:35 PM
17 Replies · 221 ViewsLast post 10/14/21, 7:03 PM by William Duffield -
by Bill Tindall, E.TN. 10/2/21, 7:30 PM
42 Replies · 416 ViewsLast post 10/13/21, 11:56 PM by David Weaver -
by David Yoho 10/13/21, 7:26 AM
3 Replies · 137 ViewsLast post 10/13/21, 9:40 PM by Don Stephan -
Round nose router bit (or veining bit)?
by JL 10/11/21, 12:24 AM
11 Replies · 185 ViewsLast post 10/12/21, 11:57 PM by Walt -
by Mike L 10/10/21, 5:47 PM
7 Replies · 292 ViewsLast post 10/12/21, 1:20 PM by Bill Tindall, E.TN.



