General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
by Jason Roehl in Mulberry, IN 4/18/07, 4:44 PM
15 Replies · 85 ViewsLast post 4/20/07, 3:30 PM by George -
Good deed for the day (or maybe corrupting...long
by JL 4/19/07, 11:53 PM
6 Replies · 48 ViewsLast post 4/20/07, 3:25 PM by JL -
Wiring needed for 3hp/220v motor?
by Joe Pack 4/19/07, 3:31 AM
9 Replies · 106 ViewsLast post 4/20/07, 2:59 PM by Joe Pack -
by Mike in VA 4/20/07, 2:05 PM
1 Reply · 66 ViewsLast post 4/20/07, 2:40 PM by Linda -
by Ernie Miller 4/19/07, 4:47 PM
9 Replies · 57 ViewsLast post 4/20/07, 12:55 PM by Bruce, a MN Galoot -
by David sparks 4/20/07, 11:55 AM
0 Replies · 38 ViewsLast post 4/20/07, 11:55 AM by David sparks -
Flattening a warped cabinet door
by Brian in SLO 4/18/07, 4:20 PM
4 Replies · 48 ViewsLast post 4/20/07, 4:30 AM by Ryan Dicker in Renfrew, Ontario -
by Jim Moore 4/17/07, 8:51 PM
16 Replies · 96 ViewsLast post 4/20/07, 2:18 AM by Don Henthorn -
by John Stump 4/19/07, 9:06 AM
5 Replies · 51 ViewsLast post 4/19/07, 10:19 PM by John in New Mexico -
Tiny Lil' Breadboards - Update
by Scott in Douglassville 4/19/07, 3:23 PM
3 Replies · 46 ViewsLast post 4/19/07, 9:03 PM by Fred West in West Chester, PA -
by Don Henthorn 4/19/07, 8:30 PM
1 Reply · 46 ViewsLast post 4/19/07, 8:41 PM by George -
by Tom Dunlap in Atlanta 4/19/07, 4:28 PM
2 Replies · 79 ViewsLast post 4/19/07, 5:50 PM by Tom Dunlap in Atlanta -
Need tape measure recommendations
by Ken Krawford 4/15/07, 7:47 PM
10 Replies · 57 ViewsLast post 4/19/07, 5:44 PM by Jeffrey D. Rose -
by Pete LaBelle 4/19/07, 2:22 PM
0 Replies · 47 ViewsLast post 4/19/07, 2:22 PM by Pete LaBelle -
Mission fumed finish on Red Oak.
by Ron Roach 4/18/07, 5:11 PM
3 Replies · 51 ViewsLast post 4/19/07, 2:11 PM by Howard Acheson -
OT - mail browser - Thunderbird?
by JL 4/17/07, 6:59 PM
17 Replies · 69 ViewsLast post 4/19/07, 12:13 PM by Curt Harms -
OT - Must See- Rube Goldberg lives! *LINK*
by Rich Pearson 4/18/07, 7:23 PM
7 Replies · 53 ViewsLast post 4/19/07, 12:13 PM by Joe -
Which came first, mortice or tenon?
by Gary Evans Tallassee, TN 4/18/07, 5:38 PM
5 Replies · 53 ViewsLast post 4/19/07, 12:00 PM by Gary Evans Tallassee, TN -
by Gary Evans Tallassee, TN 4/18/07, 5:46 PM
5 Replies · 58 ViewsLast post 4/19/07, 11:58 AM by Gary Evans Tallassee, TN -
Laminate countertop design question
by Justin Szeliga 4/18/07, 1:27 AM
2 Replies · 101 ViewsLast post 4/19/07, 3:05 AM by JackLane -
Wood movement and joinery question
by Stephen Kirk in Quakertown PA 4/18/07, 3:43 PM
7 Replies · 104 ViewsLast post 4/19/07, 2:54 AM by Stephen Kirk in Quakertown, PA -
by Ron Hildreth, Alta, Iowa 4/17/07, 11:13 PM
7 Replies · 88 ViewsLast post 4/19/07, 2:36 AM by Joe Dusel (Vista, CA) -
by Ray Thompson - Middletown,IN 4/18/07, 1:12 AM
5 Replies · 59 ViewsLast post 4/19/07, 1:11 AM by Ray Thompson - Middletown,IN -
Lee Valley on the news this morning New Tool... *LINK* 2
by Mike in Paradise 4/5/07, 10:12 AM
31 Replies · 129 ViewsLast post 4/18/07, 7:45 PM by Jim Shaver - Oakville, Ontario -
by JL 4/18/07, 5:02 PM
2 Replies · 40 ViewsLast post 4/18/07, 7:06 PM by JL -
Gordon Sampsopn's plans for router cabinet
by Larry Dubia 4/18/07, 4:11 PM
2 Replies · 88 ViewsLast post 4/18/07, 6:13 PM by Dominic Greco in Richboro PA -
by "RJ" Whelan 4/16/07, 10:49 PM
12 Replies · 65 ViewsLast post 4/18/07, 5:21 PM by "RJ" Whelan -
by Barbara Gill, Remlik VA 4/17/07, 9:16 PM
7 Replies · 44 ViewsLast post 4/18/07, 4:53 PM by Ellis Walentine -
Jet contractor saw vertical adjustment woes (long)
by Eric Kuehne 4/18/07, 1:38 AM
2 Replies · 99 ViewsLast post 4/18/07, 4:20 PM by Eric Kuehne -
by Jack Hartley 4/16/07, 6:04 PM
10 Replies · 78 ViewsLast post 4/18/07, 3:34 PM by Gary



