General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
So I spent a Lot of money this
by Dustmaker Mike 6/18/07, 12:55 AM
0 Replies · 26 ViewsLast post 6/18/07, 12:55 AM by Dustmaker Mike -
by Ellis Walentine 6/17/07, 8:42 PM
2 Replies · 39 ViewsLast post 6/17/07, 11:35 PM by Todd O. Cronkhite Maine Native, Presently Away -
by Barry Daniel-Camden, NC 6/17/07, 1:55 AM
4 Replies · 52 ViewsLast post 6/17/07, 10:16 PM by John in New Mexico -
by Joanne Adler in Pt. Pleasant, PA 6/17/07, 3:13 PM
1 Reply · 34 ViewsLast post 6/17/07, 6:55 PM by Jim Shaver - Oakville, Ontario -
OT--More on fixing the wife's hard drive
by Gary Evans Tallassee, TN 6/17/07, 2:08 AM
3 Replies · 51 ViewsLast post 6/17/07, 3:43 PM by Curly Smith -
PERSHING III : T-2 and holding . . .
by s.mackay@worldnet.att.net 6/17/07, 3:30 PM
0 Replies · 32 ViewsLast post 6/17/07, 3:30 PM by s.mackay@worldnet.att.net -
OT Kicked by a mule, eyes go crossed....
by Randy Johnson Connersville, IN 6/17/07, 12:11 PM
0 Replies · 29 ViewsLast post 6/17/07, 12:11 PM by Randy Johnson Connersville, IN -
by Paul Butz 6/12/07, 3:45 AM
21 Replies · 161 ViewsLast post 6/17/07, 2:31 AM by Wayne -
by Ernie Miller 6/14/07, 1:40 PM
11 Replies · 60 ViewsLast post 6/17/07, 2:03 AM by Wayne -
by Barry Irby 6/15/07, 10:22 PM
10 Replies · 70 ViewsLast post 6/17/07, 1:52 AM by Wayne -
A Chantix question, for Ron/Anybody OT
by Barry Irby 6/16/07, 12:28 PM
3 Replies · 101 ViewsLast post 6/16/07, 4:46 PM by Ron Hildreth, Alta, Iowa -
Hanging Inset Door, How and what Hinges?
by Alan Tolchinsky 6/15/07, 5:23 PM
4 Replies · 30 ViewsLast post 6/16/07, 4:41 PM by Dave Bair - Eaton Rapids -
by DB 6/15/07, 4:37 AM
10 Replies · 56 ViewsLast post 6/16/07, 4:34 PM by Glenn Madsen near San Francisco -
by David Hammond, in Powder Springs GA 6/13/07, 9:23 PM
15 Replies · 77 ViewsLast post 6/16/07, 3:43 PM by Bill Howatt -
by Andy Lincoln 6/15/07, 12:54 PM
9 Replies · 68 ViewsLast post 6/16/07, 2:04 PM by Al Stokka -
Small 32mm line boring machines
by Bob McGovern 6/15/07, 4:17 AM
2 Replies · 59 ViewsLast post 6/16/07, 2:03 PM by JackLane -
by Phil Joines Krum, Tx 6/15/07, 1:49 PM
8 Replies · 50 ViewsLast post 6/16/07, 12:35 PM by VLParisian -
by JL 6/13/07, 7:25 PM
7 Replies · 82 ViewsLast post 6/16/07, 2:31 AM by Jim Dillon -
by Scott Greaves in Blackfoot Idaho 6/13/07, 5:02 PM
17 Replies · 75 ViewsLast post 6/16/07, 12:36 AM by Glenn Madsen near San Francisco -
OT--fixing the wife's hard drive
by Gary Evans Tallassee, TN 6/14/07, 2:42 AM
7 Replies · 55 ViewsLast post 6/15/07, 10:51 PM by Gary Evans Tallassee, TN -
Box joint fit/ glue up question
by Pat Evans 6/15/07, 12:03 AM
8 Replies · 71 ViewsLast post 6/15/07, 9:55 PM by Rob Sandow -
All-In-One Clamp Guide? *LINK*
by JL 6/15/07, 12:28 AM
8 Replies · 67 ViewsLast post 6/15/07, 8:40 PM by JL -
"threded" knobs on Ebay *LINK*
by Grant Smith(remove 1 for email) 6/14/07, 2:24 AM
4 Replies · 45 ViewsLast post 6/15/07, 6:36 PM by Robert Henderson -
by Thomas Skaggs 6/14/07, 2:47 PM
8 Replies · 58 ViewsLast post 6/15/07, 3:31 PM by Robin Corell in Atascadero, CA -
It's always nice to have a QC inspector to inspect
by JL 6/13/07, 6:31 PM
7 Replies · 70 ViewsLast post 6/15/07, 3:02 PM by Barry Irby -
by Patrick Capobianco 6/15/07, 1:27 PM
1 Reply · 41 ViewsLast post 6/15/07, 2:50 PM by Barry Irby -
OT - Do you prefer Mary-Ann or Ginger? 2
by Mark Goodall - ATL - tooljunkie 6/12/07, 1:04 PM
32 Replies · 103 ViewsLast post 6/15/07, 2:42 PM by Todd O. Cronkhite Maine Native, Presently Away -
by Ray Thompson - Middletown,IN 6/15/07, 2:14 AM
6 Replies · 41 ViewsLast post 6/15/07, 3:50 AM by Mark Nowicki -
by Doug Barker 6/13/07, 1:07 PM
25 Replies · 109 ViewsLast post 6/15/07, 1:12 AM by Don henthorn -
by Ron Jones 6/15/07, 1:10 AM
0 Replies · 37 ViewsLast post 6/15/07, 1:10 AM by Ron Jones



