Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Dado Frustration - Long

Posts

Dado Frustration - Long

#1

Dado Frustration - Long

Scott Greaves in Blackfoot Idaho

>My tale of woe revolves around a bookcase-in-the-making that is fighting me. Last night we cut the sides, top and bottom, and the shelves, and then proceeded to cut some dadoes for the shelves. I am less than happy with the way they turned out!

We have been remodeling our cabin for the past four years, and I am now needing to make the built-ins, one bookcase and two linen closets. My Wife chose the wood she wanted, some oak veneer plywood from the orange Borg. I have a nice shop, with decent tools, if I can uncover them long enough to make anything. I have been woodturning long enough that the poor Unisaw hasn�t seen much action lately, but like the trooper it is, it still works just fine. Night before last we did all the ripping cuts on the four sheets of plywood, which went really well with three sets of hands to push, pull and balance.

But last night we needed to do the crosscuts to cut the panels for the sides, ends and shelves. We started with the bookcase because, frankly, the board on the top of the stack was the right width for the bookcase! I made the first cut on the long panel with my little Porter Cable Saw Boss, and all things considered, I thought it turned out straight and accurate, although there was some tear-out. I rough-cut the ends and shelves off the long pieces using the Saw Boss, and then cleaned them up on the table saw. So far I thought we were good.

But then came the time to set up for dadoes for the four shelves. We placed the two side panels together, and measured and marked them both for location of the dadoes. My Wife then thought we should use the fence to get the dadoes where we wanted them. This is of course dangerous, so I refused. After a little haggling, I agreed to clamp a short block to the fence so that before the workpiece got to the blade it would have cleared the block. This way we could use the fence to set a consistent measurement, without the danger of binding and kickback.

All I have to hold the pieces for crosscutting is the stock miter gauge that came with the Unisaw. I felt that I had really good control of the board, but evidently something was amiss, because after the dadoes were cut, and we placed the boards together again, I was sickened by the sight of dadoes that didn�t line up. They are not off by much, the worst by about three-sixteenth of an inch. But this is not the way I want to make anything!

Yes, we will put this together, and when we get it installed in the wall, and books are on it, we will not notice. But it will always bother me that I could not do a simple thing like get the dadoes in two boards to match up.

The worst part is that I still have two linen closet inserts to make, so two more opportunities to mess up some dadoes! Please take pity on this poor woodworker, and help me to find a way to cut my dadoes correctly, so I can be proud of my accomplishment! Is a cool new after-market miter gauge, with an extended fence the answer? Should I make a cutting sled? Please jump in and save me from future embarrassments!

And while we�re on the subject, what is it about Home Depot plywood, and variations in thickness of what should be a simple, consistent dimension?

Thanks for the help, and sorry to rant!

Scott.

Re: Dado Frustration - Long

#2

Re: Dado Frustration - Long

George@Colonel's Workshop-Havertown PA

>Good Afternoon Scott,

You are the only person I ever heard of that made that kind of mistake. I can't imagine how you can manage misplaced dados! Well, dont feel like the Lone Ranger. It just happened to me too.

I use a sled, and its easy to guage where the blade will plough. Easy as target practise, only sometimes the bull's eye moves a little. And sometimes the board moves a little during the cut. Even when I put sandpaper on the board to prevent lateral wood panel movement during the cut. Then too, I learned my fence was warped in places, and some dados were not parallel or square to the panel. All that happened to a slight degree, and can be overcome and corrected.

My project will involve face frames, which hide many mistakes. the major trick is to get the shelves horizontal and parallel, then glue and clamp and screw. Good luck. I feel better knowing my misery has company.

George

Re: Dado Frustration - Long

#3

Re: Dado Frustration - Long

Thomas Skaggs, Foothills of Mount Level

>I agree with the Colonel that a simple sled can be a good solution. Another way to go is a router. You could use a straight cutting bit or a straight spiral bit. Clamp a staight edge to use as a guide for each pass.

Tom

Re: Dado Frustration - Long

#4

Make one of these and never look back *LINK*

Grant Smith

>Here's what I made for making dado's. I LOVE it! just use your shelf material to set the width, and the cheap BORG plywood will not ruin your project if its thickness varies.

Oh, and if you have the time, make yourself two of them... one longer than the other for later use. I'd make one for widths up to about 12", and then one for widths up to about 34" or so for cabinets and desks.

Repeat after me: "This is THE way to cut dado's!"

Regards,

Grant in Iowa


Router dado jig

Re: Dado Frustration - Long

#5

Re: Oh, and ...Uh...one more thing:

Grant Smith

>Don't rip your shelf sides to finished width before you cut the dado's. Instead, leave your sheet stock the width of both sides plus a saw kerf. Then make your dado's in one pass before ripping the panel into the two shelf sides. It is less work this way setting up the dado jig, and so long as your dado jig is set up square to the edge(and your stock is square), they will match perfectly left to right.

I also agree that a table saw sled is in order and would be another way to make the cuts.

Re: Dado Frustration - Long

#6

Re: Dado Frustration - Long

Ted Wong

>It's a common mistake and on bookcases where the lengthes may be 6' or more and the width 12" or less it is problematic to use the fence as your guide and the long pieces can be difficult to control with miter gauge. My solution is to use a router and a straight edge squared to the edges with a framing square. Another stategy is to leave the piece a little wider than your two sides combined, cut the dados, and rip the pieces after the grooves have been routed.

Re: Dado Frustration - Long

#7

Thanks!

Scott Greaves in Blackfoot Idaho

>Wow! Thanks guys! A router - who'd of thunk it? Yes, that would be much easier than what I was attempting. Grant, that jig looks like just the ticket, but I'm not sure if any of my routers are set up to mount a guide bushing. Time to find out! Regardless, I think a new cutting sled is in order as well. I hope to report good results soon!

Scott.

Re: Dado Frustration - Long

#8

Re: Thanks!

Thomas Skaggs, Foothills of Mount Level

>Grant's jig suggestion is a good one. But in a pinch clamping a piece of scrap with a straight edge to your work would do in a pinch. A firm steady hand is recommended. Depending on the depth you may want to do it in multiple passes, a little deeper each time...to avoid overloading the bit.

Tom

Re: Dado Frustration - Long

#9

Re: Dado Frustration - Long *LINK*

David Yoho

>Here's the way I do it accurately -

David


Accurate dado cuts using the router

Re: Dado Frustration - Long

#10

Measure once, rout twice

Curly Smith

>If, like me, you don't particularly like measuring things more than once you might consider an additional router "jig". Most people would call it a work table.

I use my circular saw table (a fold-up table built from 2x2's) but a few sawhorses and a sheet of 3/4" plywood will suffice. Set the table up and clamp or screw a cleat along the edge parallel to the dadoes. Set your router guide (I use a homemade t-square) to make the first dado then clamp or screw a stop block to the side opposite the router. Rout the dado. Locate your next dado, move the router guide and clamp or screw another stop block. When you're finished with the first piece simply slide the matching piece onto the table, butt it against the cleat and the stop blocks, set your guide against the stop blocks and rout away.

Your dadoes still might not be in the right place will they will all be in the same wrong place.

Measure once, rout twice.

Re: Dado Frustration - Long

#11

guide bushing not needed

Carlos Clarke

>I built the same jig. The guide bushing isn't needed.

Run the router against the edge and it will cut the

jig to size. Keep that edge of the router against the

jig edge and always use the same bit.

Works great.

Re: Dado Frustration - Long

#12

Re: Dado Frustration - Long

Paul Waddle

>I agree,cut your dadoes before ripping the pcs. Make sure you are straight and pallel to the edge you are cutting. I suppose you could use a skill saw. Now one straight edge is fine for those who don't have those nasty gremlins aoround,but I prefer to box my router on both sides so it won't stray off. (if you have already cut your pcs, lay them edge to edge and rout across the pair-this works fine if you want to cut all the way across-has draw backs if you don't). pw

Re: Dado Frustration - Long

#13

I use this and it's excellent

Alan Tolchinsky

>

Re: Dado Frustration - Long

#14

Re: Ditto

Grant Smith(remove 1 for email)

>Yeah, I googled up that plan for the jig. Mine actually doesn't use the bushing either. I put an arrow on my router so I can always keep that edge oriented in one direction for accuracy. And you make the jig such that on the first pass the router actually cuts a bit of the jig board away. From that point on, it is very accurate in my experience. It actually is so accurate that the dado's end up a bit tight. You might do a test run and then if the dado is too tight add a piece of paper next to your shelf piece when setting the jig to allow enough slop for glue space and easier assembly.

Regards,

Grant in Iowa

Re: Dado Frustration - Long

#15

Re: Make one of these and never look back

John in Calgary

>I also have one of these jigs and really like it, in fact I just pulled it out again this weekend to use. There are only two downsides - how do you clamp it to your work piece (hm, now that I look at the photo again, I see that it isn't, the work piece is clamped to your bench and so is the jig) and the amount of flex along the length of the jig if you only clamp it on one side (which would be fixed by clamping it to the bench).

Re: Dado Frustration - Long

#16

Safety issue on table saw?

Stephen Kirk in Quakertown PA

>Not to let the poor table saw out of the mix, but I routinely use mine to cut dadoes using the fence to control distance. I won't do this on something that is bigger than the saw table (unless I add support). However, I don't think that this is an unsafe activity. During a dadoe cut, the blade is buried in the wood and you don't have a stray bit between the blade and the fence to kick back.

Using the table saw, you can either use a dado stack or make some shims that go against the fence which you can add/remove to get to the width of the dadoe.

I think I recall watching Norm do this on a lot of projects. I only use a short stop block at the leading edge of the fence if I'm cutting a piece off of a board and it could become trapped between the fence and blade.

Can anyone else confirm/deny my logic? I'd rather not be doing something I didn't know was unsafe.

Re: Dado Frustration - Long

#17

Re: Dado Frustration - Follow-up

Scott Greaves in Blackfoot Idaho

>Thanks again for all the great input on this subject!

Yesterday I got to spend the day driving my Dad to the local VA Hospital to get some new shoes, so afterwards we stopped by a good tool store (M&M Tools in Salt Lake City) so I could get the 1/2" straight bit for the router. Well, you know how it is, being surrounded by all those tools and all, I ended up getting a new Porter Cable router (the smaller one, a 690?), the bit and I even opted for the template guides. When I told my Wife, she just said "Happy Father's Day!"

Tonight we're building the jig, and going to try and rout some dadoes! Wish me luck!

Scott.

Re: Dado Frustration - Long

#18

Re: Dado Frustration - Follow-up

Glenn Madsen near San Francisco

>Those are nice tools, Scott. You should be able to do a pretty good job with them for many years.