Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

Exterior finishes?

Posts

Exterior finishes?

#1

JL

Exterior finishes?

JL

>I have been asked to build/rebuild some outdoor benches.

They would like a clear finish.

The finishes that are available around here are what are available at H.D., Lowes and Ace Hardware. I am going down to the big city on Saturday, so I could stop by Rockler or Woodcraft so I could pick up a gallon of "Outdoor Oil" by General Finishes or whatever else.

Any suggestions?

Re: Exterior finishes?

#2

Re: Exterior finishes?

Clint Searl, at the base of Haycock Mtn

>If you want a film type finish, Behr clear waterborne one part epoxy garage floor finish is good on wood, also. Just be sure to coat the wood all around.

jamestowndistributers.com carries many marine finishes.

Clint

Re: Exterior finishes?

#3

Re: Exterior finishes?

Steve Schoene

>I doubt epoxy would be good on wood that lives in the sun, though I don't know that particular product. Epoxy has no natural UV resistance and UV absorber's can't be added I don't believe.

There are NO clear finishes at the Big Boxes or Ace Hardware (unless you are in one of a few yachting mad towns) that are acceptable for wood in sunshine.

Oil finishes can work, but to keep the wood from turning grey, it will need to be cleaned and a maintenance coat added several times each year. (Monthly in full sun below New England latitudes)

For film finishes you only want good marine spar varnish. There are three brands of good marine spar. Epifanes Clear High Gloss, Interlux Schooner, and Pettit Captain's. Follow the instructions, including the requirement of using 6-8 coats. They are only available boating supply stores. Jamestown Distributors mentioned above is good, and www.defender.com offers quite good prices. Even with these products an annual (or bi-annual if there is quite a bit of shade)scuff sanding and an additional coat of finish is necessary.

I suppose there are two part finishes such as Interlux Perfection that could be quite satisfactory, but these are at least $60 a quart for the material, but you will also need the $19 per quart thinner. You will also likely need a new brush for each coat applied.

Re: Exterior finishes?

#4

JL

Re: Thanks...

JL

>While there are boats and boat stores around here (Lake Nottely and Lake Chatuge), there are no yacht places :). I'll try for an oil finish then.

Re: Exterior finishes?

#5

Re: Exterior finishes?

Jesse in New Mexico

>Hey Steve,

I use a finishing technique from an article in FWW a couple of years ago. You use clear penetrating epoxy sealer and spar varnish. You let the last coat of epoxy get half dry, then apply a 25% thinned coat of varnish. The article says they make a strong chemical bond. The epoxy protects from water, the varnish provides some UV protection. Works out here in the high desert sun. But I agree, an annual touchup of the varnish is needed.

Re: Exterior finishes?

#6

Re: Exterior finishes?

Paul Dwight

>I've given up using clear film-forming finishes on unprotected outdoor wood. It's just too much work trying to stay ahead of the inevitable deterioration of the finish. If you get too far behind and the finish deteriorates too much, you're looking at stripping and refinishing. Yech.

For unprotected outdoor wood, I use an "in the wood" type product that protects against graying, gives a little water resistance and, most importantly, is VERY easy to renew. You just brush on a new coat when the old one starts to look dingy. The product I use is Olympic Maxximum, which I buy at Lowes. The "clear" version of this product isn't really clear -- it adds a rather orange-ish cast to the wood -- so you might want to try it on some scrap to be sure you can live with the effect. I live in the desert, so the wood sees a ridiculous amount of sunshine but very little rain, and I usually end up brushing on a new coat about every 6 months or so.

Hope this helps. -- Paul

Re: Exterior finishes?

#7

Re: Exterior finishes?

Mike in VA

>I've tried several clear finishes on the redwood rails on my deck, and the best by far is the Cetol Translucent made by Sikkens. I did them two years ago and they still look great, with no peeling. I don't think HD carries this, but ACE might. I got it at a local building supply store.

Re: Exterior finishes?

#8

Re: Exterior finishes?

Jim Dillon

>Mike,

That is good to know regarding Sikkens clear finish. I've had very good luck with Sikkens stains for outdoor use. But, having said that, I am lately coming down on the side of either no finish (and just let the wood weather to a nice gray) or an easily renewable non-film forming finish.

Jim