General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
How did you get started in woodworking?
by Carol - now in NC Nebraska 9/8/07, 2:05 PM
20 Replies · 94 ViewsLast post 9/11/07, 2:16 AM by Carol - now in NC Nebraska -
Questions on Rubbing out a finish.
by Barry Irby 9/10/07, 11:30 PM
2 Replies · 35 ViewsLast post 9/11/07, 2:06 AM by Steve Schoene -
by Steve Bellner 9/10/07, 3:41 AM
4 Replies · 41 ViewsLast post 9/11/07, 1:53 AM by Don henthorn -
Curio-Tempered glass - options
by Dan Manturi 9/9/07, 12:30 PM
10 Replies · 200 ViewsLast post 9/11/07, 12:54 AM by Dan Manturi -
by Stokes 9/10/07, 11:00 AM
11 Replies · 71 ViewsLast post 9/11/07, 12:07 AM by Ellis Walentine -
House reno pics, soffit detail question. (w/pics)
by David Eisan 9/10/07, 1:38 AM
6 Replies · 47 ViewsLast post 9/10/07, 11:40 PM by Jason Roehl in Lafayette, IN -
by Mike Baker 9/10/07, 2:57 PM
5 Replies · 32 ViewsLast post 9/10/07, 10:26 PM by Mike Baker -
by ted Wong 9/10/07, 9:45 PM
0 Replies · 29 ViewsLast post 9/10/07, 9:45 PM by ted Wong -
by Mark Goodall - ATL - tooljunkie 9/10/07, 11:27 AM
2 Replies · 36 ViewsLast post 9/10/07, 8:56 PM by jeff -
Those Royals and their collections *LINK*
by jtsmithers 9/10/07, 4:13 PM
1 Reply · 30 ViewsLast post 9/10/07, 8:46 PM by Tom Sontag -
Heads up! Low price for GRR-RIPPER 200 *LINK*
by David Barnett - SW Florida 9/10/07, 5:59 PM
2 Replies · 36 ViewsLast post 9/10/07, 7:52 PM by David Barnett - SW Florida -
by Steve Yakoban 9/9/07, 2:46 PM
7 Replies · 78 ViewsLast post 9/10/07, 7:35 PM by Dave Mount -
by tom chapman 9/8/07, 7:34 PM
3 Replies · 34 ViewsLast post 9/10/07, 4:52 PM by Dave Bair - Eaton Rapids -
by JL 9/7/07, 9:46 PM
5 Replies · 35 ViewsLast post 9/10/07, 3:34 PM by knotscott -
dewaltservicenet.com - need bearings!
by Sue McLam in Orange, VT 9/9/07, 8:51 PM
7 Replies · 38 ViewsLast post 9/10/07, 2:25 PM by Phil Joines Krum, TX -
by Tom Pilsbury 9/7/07, 7:37 PM
6 Replies · 44 ViewsLast post 9/10/07, 1:41 PM by Kevin Rabenaldt -
by George (Oxford, NC) 9/9/07, 10:00 PM
2 Replies · 34 ViewsLast post 9/10/07, 1:34 PM by Danny Wells -
by Jess Bunch 9/9/07, 5:00 AM
6 Replies · 50 ViewsLast post 9/10/07, 12:44 PM by Mike Fitterling -
Ok...about drill presses *LINK*
by HC Sakman 9/9/07, 7:45 AM
14 Replies · 61 ViewsLast post 9/10/07, 6:34 AM by Carol - now in NC Nebraska -
by DB 9/10/07, 5:02 AM
0 Replies · 25 ViewsLast post 9/10/07, 5:02 AM by DB -
Tool Gloat - Tormek found on eBay
by Ray Carson, Lawrenceville NJ 9/7/07, 2:38 PM
7 Replies · 58 ViewsLast post 9/10/07, 2:03 AM by Brian in Brighton -
OT--Transmission problem, '93 Explorer
by Gary Evans Tallassee, TN 9/9/07, 10:11 PM
6 Replies · 39 ViewsLast post 9/10/07, 1:57 AM by Dale Lenz -
by Mitch from TN 9/8/07, 11:21 PM
3 Replies · 33 ViewsLast post 9/10/07, 12:59 AM by JKJ in East TN -
by Barry Irby 9/8/07, 11:52 PM
5 Replies · 37 ViewsLast post 9/10/07, 12:52 AM by JKJ in East TN -
by ben d. 9/9/07, 11:25 PM
0 Replies · 29 ViewsLast post 9/9/07, 11:25 PM by ben d. -
Lacquer and ammonia based cleaners
by Gary Camp Bend, Oregon 9/9/07, 7:41 PM
5 Replies · 80 ViewsLast post 9/9/07, 10:30 PM by Gary Camp Bend, Oregon -
by Gary Evans Tallassee, TN 9/8/07, 10:46 PM
4 Replies · 29 ViewsLast post 9/9/07, 10:05 PM by Gary Evans Tallassee, TN -
by Jess Bunch 9/9/07, 5:07 AM
3 Replies · 37 ViewsLast post 9/9/07, 9:22 PM by Jess Bunch -
by Barry Irby 9/8/07, 11:45 PM
10 Replies · 67 ViewsLast post 9/9/07, 7:30 PM by Lee Schierer - McKean, PA -
NEW Shop Shots - Finished Projects!
by David Yoho 9/9/07, 5:44 PM
0 Replies · 38 ViewsLast post 9/9/07, 5:44 PM by David Yoho



