General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
by Mike H 2/7/08, 6:45 PM
6 Replies · 36 ViewsLast post 2/8/08, 5:08 PM by Dave Bair - Eaton Rapids -
OT Camera Battery Question Again
by Barry Irby 2/7/08, 8:18 PM
8 Replies · 24 ViewsLast post 2/8/08, 4:57 PM by Larry Clinton At Frankfort (Central)., Indiana -
Thoughts on finishing birds-eye maple.
by Paul Kierstead 2/4/08, 8:09 PM
12 Replies · 41 ViewsLast post 2/8/08, 4:51 PM by Paul Kierstead -
by Jesper, Denmark 2/7/08, 11:09 PM
1 Reply · 27 ViewsLast post 2/8/08, 3:49 PM by Hank Knight -
by Doug Ridley 2/7/08, 12:14 PM
9 Replies · 112 ViewsLast post 2/8/08, 1:53 PM by Barry Irby -
by scottinphoenix 2/8/08, 12:07 AM
3 Replies · 40 ViewsLast post 2/8/08, 12:57 PM by George (Oxford, NC) -
by Jim Runchey 2/6/08, 10:09 PM
8 Replies · 26 ViewsLast post 2/8/08, 12:36 PM by Curt Harms -
Becoming a pro furnituremaker/ cabinetmaker
by Nick Dombrowski 2/7/08, 3:56 AM
5 Replies · 30 ViewsLast post 2/8/08, 4:45 AM by Dick Coers -
by Starry Chan, Saratoga, CA 2/8/08, 4:31 AM
1 Reply · 19 ViewsLast post 2/8/08, 4:44 AM by Joe Pack -
by Joe Pack 2/7/08, 5:23 AM
8 Replies · 50 ViewsLast post 2/8/08, 4:36 AM by Joe Pack -
Rikon 18" w/2.5HP motor, downsides?
by Craig Daymon 2/7/08, 6:20 PM
3 Replies · 41 ViewsLast post 2/8/08, 4:25 AM by Dick Coers -
by Ron Hildreth 2/8/08, 12:10 AM
2 Replies · 119 ViewsLast post 2/8/08, 3:09 AM by Mark Mandell - Gone Round In Jersey -
by David Best 2/7/08, 1:29 PM
7 Replies · 38 ViewsLast post 2/8/08, 1:04 AM by Bill Tindall, E.TN -
OT - Laptop Memory Upgrade Problem
by Scott Greaves in Blackfoot Idaho 2/7/08, 7:45 PM
3 Replies · 29 ViewsLast post 2/8/08, 12:37 AM by John K Jordan -
OT - Looking for very thin plastic sheeting
by Mark Goodall - ATL - tooljunkie 2/6/08, 8:36 PM
18 Replies · 41 ViewsLast post 2/7/08, 11:43 PM by John K Jordan -
by David in Seattle 2/6/08, 6:04 PM
10 Replies · 38 ViewsLast post 2/7/08, 11:03 PM by Geoff (in Madison) -
OT-Reflective prismatic film *LINK*
by Frank Orfanello 2/7/08, 1:56 AM
5 Replies · 24 ViewsLast post 2/7/08, 11:02 PM by Frank Orfanello -
by David Hay @ Denver 2/4/08, 4:05 PM
7 Replies · 63 ViewsLast post 2/7/08, 9:52 PM by Rick L -
how deep should hole in bowl gouge handle be?
by RogerC 2/7/08, 8:29 PM
2 Replies · 23 ViewsLast post 2/7/08, 8:34 PM by RogerC -
by Dustmaker Mike 2/7/08, 4:08 PM
1 Reply · 20 ViewsLast post 2/7/08, 8:32 PM by MN deepwoods (Dave) -
Thank you Grant Smith -- cordless batteries
by Tim Greif - West of Chicago 2/7/08, 3:22 PM
2 Replies · 30 ViewsLast post 2/7/08, 6:45 PM by Ellis Walentine -
by Jeff 2/6/08, 5:16 PM
9 Replies · 37 ViewsLast post 2/7/08, 5:06 PM by robert davis -
by Steve Silca 1/29/08, 1:53 PM
27 Replies · 84 ViewsLast post 2/7/08, 4:22 PM by Chuck Kettler Greenwood IN -
OT-Memphis Storms - U OK Tony?
by Rick Jackson, TN 2/6/08, 9:06 PM
5 Replies · 30 ViewsLast post 2/7/08, 6:30 AM by Martin from Granbury -
by MikefromTn 2/7/08, 2:09 AM
0 Replies · 23 ViewsLast post 2/7/08, 2:09 AM by MikefromTn -
by Eddie Pacheco; San Jose, Ca. 2/5/08, 5:31 PM
3 Replies · 25 ViewsLast post 2/7/08, 1:46 AM by Johanna -
by Howard 2/4/08, 10:53 PM
3 Replies · 18 ViewsLast post 2/7/08, 12:44 AM by John K Jordan -
OT: What work generally requires a permit?
by Dan Mitchell 2/6/08, 3:47 AM
11 Replies · 46 ViewsLast post 2/6/08, 11:51 PM by Dan Mitchell -
by Joe Wynsma 2/6/08, 3:26 AM
1 Reply · 20 ViewsLast post 2/6/08, 11:17 PM by Ed Mulligan -
by Bear 2/5/08, 2:42 AM
6 Replies · 34 ViewsLast post 2/6/08, 8:58 PM by don at central illinois



