General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
by Ken Oakley-Sunny St. Cloud, Fla. 2/20/09, 2:04 PM
19 Replies · 17 ViewsLast post 2/22/09, 8:54 PM by North of the Border -
by Lee Schierer - McKean, PA 2/21/09, 2:37 PM
13 Replies · 19 ViewsLast post 2/22/09, 8:53 PM by Bill Houghton -
Inquiring of the computer guru's - again
by Carol - now back in Dubuque, IA 2/13/09, 11:21 PM
3 Replies · 16 ViewsLast post 2/22/09, 6:58 PM by Lowell Kinzer -
Woodworkers Helping Soldiers *LINK*
by Lee Gordon 2/22/09, 6:27 PM
0 Replies · 15 ViewsLast post 2/22/09, 6:27 PM by Lee Gordon -
Bending wood - steaming vs. bathtub
by Steve Silca 2/22/09, 4:20 PM
2 Replies · 21 ViewsLast post 2/22/09, 6:05 PM by Mark Mandell - Gone Round In Jersey -
by Jim Engel 2/22/09, 2:44 AM
3 Replies · 23 ViewsLast post 2/22/09, 5:50 PM by Jim Engel -
Oak grain-raising in finishing .....
by Larry Rupprecht 2/22/09, 4:06 PM
0 Replies · 17 ViewsLast post 2/22/09, 4:06 PM by Larry Rupprecht -
by Paul Storck 2/21/09, 8:06 PM
5 Replies · 27 ViewsLast post 2/22/09, 3:40 PM by Paul Storck -
bentwood lamination w/ vacuum press
by Grant in Iowa 2/21/09, 9:51 PM
6 Replies · 49 ViewsLast post 2/22/09, 3:11 PM by Grant in Iowa -
by Tom MacGregor 2/21/09, 9:08 PM
10 Replies · 25 ViewsLast post 2/22/09, 1:50 PM by Bill Tindall, E.TN -
by Frank in Forest Hill 2/21/09, 12:28 PM
4 Replies · 9 ViewsLast post 2/22/09, 4:04 AM by Bill Houghton -
by John_in_Az 2/22/09, 1:28 AM
3 Replies · 39 ViewsLast post 2/22/09, 3:51 AM by Keith Newton------WebKitFormBoundaryV6MZb+tiOpocz6 -
by Frank Orfanello 2/20/09, 3:12 PM
15 Replies · 56 ViewsLast post 2/22/09, 2:23 AM by Frank Orfanello -
by Hal B. 2/21/09, 9:06 PM
4 Replies · 10 ViewsLast post 2/22/09, 1:09 AM by Fred Davis -
by Kurt in Minnesota 2/21/09, 1:44 AM
2 Replies · 10 ViewsLast post 2/21/09, 5:34 PM by Pete in Holland, MI -
by Bruce, a MN Galoot 2/20/09, 8:25 PM
6 Replies · 24 ViewsLast post 2/21/09, 5:30 PM by Bruce, a MN Galoot -
by Barry Irby 2/21/09, 2:49 PM
4 Replies · 14 ViewsLast post 2/21/09, 4:28 PM by Barry Irby -
Can I use Holly Wood for anything?
by James Scott 2/20/09, 12:06 AM
14 Replies · 78 ViewsLast post 2/21/09, 3:52 PM by Barry Irby -
OT - I need a volunteer Visual Basic guru :)
by Paul Cates - Henderson, KY 2/20/09, 9:04 PM
5 Replies · 24 ViewsLast post 2/21/09, 2:21 PM by Dave Paine -
by JL 2/20/09, 10:00 PM
6 Replies · 41 ViewsLast post 2/21/09, 1:50 PM by Jim Dillon -
OT need Microsoft office option
by Wayne Carson 2/21/09, 3:14 AM
4 Replies · 15 ViewsLast post 2/21/09, 1:26 PM by Jim Dillon -
57 chevy low angle block plane
by Bob Boswood 2/18/09, 6:51 PM
11 Replies · 62 ViewsLast post 2/21/09, 2:44 AM by Bill Houghton -
by John K Jordan 2/18/09, 8:35 PM
3 Replies · 10 ViewsLast post 2/20/09, 9:31 PM by Pat Riley -
OT- 1x1 mesh tile backsplash - notch or V trowel?
by Steve Silca 2/20/09, 7:59 PM
2 Replies · 17 ViewsLast post 2/20/09, 8:24 PM by Jon Weisenbach -
I really didn't expect my messy shop
by JL 2/18/09, 7:57 PM
3 Replies · 14 ViewsLast post 2/20/09, 6:01 PM by Bill Tindall, E.TN -
WC Weekend Accomplishments....
by Dennis E. Peacock 2/16/09, 1:56 PM
13 Replies · 33 ViewsLast post 2/20/09, 5:51 PM by Frank Orfanello -
by steve mackay 2/17/09, 4:41 PM
15 Replies · 28 ViewsLast post 2/20/09, 4:30 PM by steve mackay -
by George 2/20/09, 2:45 AM
4 Replies · 12 ViewsLast post 2/20/09, 4:10 PM by George -
by Alan Young 2/18/09, 11:58 PM
19 Replies · 53 ViewsLast post 2/20/09, 2:09 PM by steve antonucci -
Electric hand planer on a large flat surface?
by Mat 2/17/09, 6:13 AM
4 Replies · 35 ViewsLast post 2/20/09, 12:27 PM by Ed Mulligan



