General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
Question about a "roll top table"
by Bill Tindall, E.TN. 10/31/13, 12:51 AM
1 Reply · 20 ViewsLast post 10/31/13, 2:42 AM by Bill Houghton -
by JL 10/29/13, 5:27 PM
5 Replies · 65 ViewsLast post 10/30/13, 6:57 PM by Joseph Mulherin, sr -
Is there a name for this type of work?
by Gary Smyth 10/30/13, 4:29 PM
2 Replies · 24 ViewsLast post 10/30/13, 6:23 PM by Sgian Dubh -
Poplar & Maple Rough - Truckload
by ckverdurmen 10/30/13, 12:35 PM
0 Replies · 41 ViewsLast post 10/30/13, 12:35 PM by ckverdurmen -
by Ralph Lipeles 10/29/13, 7:13 PM
5 Replies · 25 ViewsLast post 10/30/13, 12:28 PM by A.J. Hamler -
WC Weekend Accomplishments....
by Dennis E Peacock 10/28/13, 1:26 PM
3 Replies · 32 ViewsLast post 10/29/13, 4:42 PM by Joe -
by Gary Smyth 10/28/13, 1:28 PM
5 Replies · 36 ViewsLast post 10/29/13, 4:41 PM by Brian in SLO -
by Thomas Skaggs 10/15/13, 4:40 PM
20 Replies · 31 ViewsLast post 10/29/13, 4:03 PM by Roger Rayburn -
Tuesday Night Hand Tool Chat - new v old
by Stephen Shepherd 10/29/13, 3:15 PM
0 Replies · 26 ViewsLast post 10/29/13, 3:15 PM by Stephen Shepherd -
by Gary Smyth 10/25/13, 1:36 PM
6 Replies · 20 ViewsLast post 10/28/13, 8:22 PM by Larry in nw ohio -
Daughters desk. Done. Almost...
by Joe 10/23/13, 12:52 PM
9 Replies · 37 ViewsLast post 10/28/13, 4:21 PM by Bill Tindall, E.TN. -
by Tom Pilsbury (Chicago) 10/26/13, 2:11 AM
7 Replies · 25 ViewsLast post 10/28/13, 2:58 PM by Tom Pilsbury (Chicago) -
No show from the Ginkgos in Peoria, IL this year
by Dick Coers 10/26/13, 2:25 AM
6 Replies · 18 ViewsLast post 10/28/13, 2:00 PM by Kevin French -
OT; basement insulation question
by Mark Hennebury 10/26/13, 3:51 PM
8 Replies · 16 ViewsLast post 10/27/13, 3:12 PM by Mark Hennebury -
by Rod Peterson—Ormond Beach, FL 10/26/13, 10:29 PM
2 Replies · 18 ViewsLast post 10/27/13, 1:36 PM by Joanne in Point Pleasant, PA -
Has anyone tried carbide insert router bits?
by John in NM 10/26/13, 1:42 AM
4 Replies · 24 ViewsLast post 10/27/13, 1:05 AM by Robin Corell in Atascadero,CA -
by JL 10/26/13, 1:24 AM
2 Replies · 25 ViewsLast post 10/26/13, 2:53 PM by Jason Roehl in Lafayette, IN -
by McKay 10/25/13, 2:41 PM
3 Replies · 21 ViewsLast post 10/25/13, 11:36 PM by McKay -
Making a lateral file - Where to get hardware?
by JL 10/25/13, 9:14 AM
4 Replies · 41 ViewsLast post 10/25/13, 4:50 PM by JL -
Joining Short Moulding Into Long
by John McGaw 10/23/13, 5:07 PM
20 Replies · 90 ViewsLast post 10/25/13, 1:35 PM by John McGaw -
by james runchey 10/23/13, 7:28 PM
5 Replies · 18 ViewsLast post 10/24/13, 3:50 PM by Jerry Nicholson -
refinishing rosewood totes, etc
by ray 10/19/13, 2:29 AM
8 Replies · 73 ViewsLast post 10/24/13, 2:01 PM by Keith Newton -
WC Weekend Accomplishments....
by Dennis E Peacock 10/21/13, 12:50 PM
13 Replies · 39 ViewsLast post 10/23/13, 10:51 PM by John in NM -
Fun with Science - Rust Removal
by Stephen Kirk 10/21/13, 12:33 AM
11 Replies · 36 ViewsLast post 10/23/13, 11:46 AM by Bill Tindall, E.TN. -
Wobbly "modesty panel" - how to deal with it?
by JL 10/22/13, 12:06 PM
16 Replies · 57 ViewsLast post 10/23/13, 7:43 AM by psenn -
by Thomas Skaggs 10/21/13, 7:15 PM
17 Replies · 57 ViewsLast post 10/23/13, 3:07 AM by Bill Tindall, E.TN. -
A&C Home -- Worth a look *LINK*
by Ellis Walentine 10/21/13, 9:50 PM
5 Replies · 15 ViewsLast post 10/22/13, 9:12 PM by Thomas Skaggs -
by Charles Yawn 10/21/13, 1:02 PM
3 Replies · 17 ViewsLast post 10/22/13, 3:20 PM by BrianMonumentCO -
Beginner's Vacuum Bagging Advice
by John McGaw 10/17/13, 9:57 PM
10 Replies · 68 ViewsLast post 10/22/13, 12:46 AM by Keith Newton -
Looking for old article on scavenging motors
by Henry Higginbotham 10/21/13, 12:45 AM
10 Replies · 20 ViewsLast post 10/21/13, 8:30 PM by Jerry Gibbs



