Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

refinishing rosewood totes, etc

Posts

refinishing rosewood totes, etc

#1

refinishing rosewood totes, etc

ray

I just started to clean up a few rosewood totes and knobs. They appear to darker than some of the restored samples I have seen.

Does rosewood darken significantly with age?

What should I be using to clean these to a point where the wood figure is apparent?

Best oil/finish/wax to keep them from going dark immediately?

If the darkening is caused by time/oxidation, can I sand sufficiently to lighten without changing the contours, etc?

Thanks

Re: refinishing rosewood totes, etc

#2

craigd

Re: refinishing rosewood totes, etc

craigd

The rosewood totes/knobs I've refinished (many, mostly Stanley) have finished with lacquer, I've seen the rare shellac'd one, so alcohol or lacquer thinner will remove most of the finish. I usually sand 150 to 320 and then 0000 steel wool, at which point the surface will be nice and shiny. I rarely see much color change, just more figure and the color seems stable (at least for several days). I either apply lacquer or shellac, wax would probably work nicely. Ones I've refinished over five years ago haven't changed color. If you use oil, expect dark, which can be nice if that is what you like.

The colors of the wood [I have] range from light milk chocolate to dark, dark chocolate, sometimes with orangeish tints.

Re: refinishing rosewood totes, etc

#3

Re: refinishing rosewood totes, etc

Ron in Sterling, CT

Ray,

I have finished numerous totes and knobs over the last 20 years. I also find quite a variance in the darkness of the rosewood, but the color of each tote is stable, i.e. doesn't change much. I clean like Craig does, but usually only go to 220 grit. I have used Lacquer, and shellac, but have finally settled on using TruOil. I clean them with alcohol just before finishing, then rub on a coat of TruOil. I use a fine pad to finish between coats if I can feel any dust nibs, otherwise I apply another coat. I usually apply 3 or 4 coats depending on how bad a shape the piece was it to begin with. It gives me a nice shine with no wax needed. My 2 cents.

Good Luck

Re: refinishing rosewood totes, etc

#4

Re: refinishing rosewood totes, etc

Steve Mackay

I've done more than my share. I also go down to #220. I don't think going any further is accomplishing a whole lot. And I like to leave some material for the next guy. I finnish with water poly because I like the "tac". My grip ain't what it used to be. But yes, it DOES come out pretty dark.

Re: refinishing rosewood totes, etc

#5

Re: refinishing rosewood totes, etc

Bill Houghton, Sebastopol, CA

Minority opinion here: I use MinWax or Danish Oil - a long oil varnish. Gives a soft, smooth feeling to the piece; feels good in the hand. It's not as dramatic as a film finish, but it'll be easier to repair if it wears.

I don't recall to what sanding level I got when I did my last tote. 220 sounds about right.

Re: refinishing rosewood totes, etc

#6

doesn't it depend on objective?

Bill Tindall, E.Tn.

Personally I have never had the urge to do anything. But, it would seem that what was appropriate would depend on the objective of this effort. If planes are like most else there is a "right" and unacceptable way to clean, restore conserve, for "collector" preferences. For personal use again one would need to decide if the effort was to restore to new condition, "clean-up which might just involve waxing, conserve, etc. Somehow sanding does not seem right for any objective. Sanding certainly is not necessary to remove grime or old finish. The finish to be put back on again depends on objective. For things that hands touch in use, be it canoe paddle, gun stock or wood plane parts, oil is best. For that new from the box look lacquer or shellac might be best. For a restoration, whatever was used to begin with is the answer.

Re: refinishing rosewood totes, etc

#7

Ellis Walentine

Brazilian rosewood darkening

Ellis Walentine

I have some old Brazilian rosewood that is quite dark, and the color goes through and through. I wouldn't try to sand back to bright colored wood. And, based on some experiments I did long ago, don't even think about bleaching it. The dark wood still retains the landscape figure, but it is quite subtle.

Ellis

Re: refinishing rosewood totes, etc

#8

Re: Brazilian rosewood darkening

ray

Thanks for the assistance. I will learn to live with the dark side of the rosewood that was used on my type 7 plane.

Thanks again

Re: refinishing rosewood totes, etc

#9

Re: Brazilian rosewood darkening

Keith Newton

Ray, I believe BR is one of those woods which will darken initially, but will continue to get lighter through the years, when it is exposed to UV. Some of the earlier posters suggest it just continues to darken, which may be true for something that lives in a box, but I've seen plenty of furniture sitting too close to a big window that ended up as light as W Oak.