Hand Tools
Traditional tools, sharpening, restoration, usage techniques.
Related: Hand Tools archive
Topic list
-
TopicStatisticsLast post
-
by Stephen Shepherd in the State of Deseret 3/4/08, 12:21 PM
3 Replies · 19 ViewsLast post 3/4/08, 6:38 PM by Stephen Shepherd in the State of Deseret -
by Stephen Shepherd in the State of Deseret 3/1/08, 9:47 PM
10 Replies · 25 ViewsLast post 3/4/08, 4:57 PM by Ernie Miller -
by Bill Houghton 3/1/08, 9:11 PM
7 Replies · 88 ViewsLast post 3/4/08, 9:23 AM by paul womack -
by Derek Cohen (in Perth, Australia) 3/2/08, 12:24 PM
12 Replies · 108 ViewsLast post 3/4/08, 5:59 AM by ThomD -
Rubberized abrasives for sharpening
by Dave Mount 3/2/08, 3:21 PM
3 Replies · 38 ViewsLast post 3/3/08, 8:51 PM by Doug Reynolds in Seattle -
Woodworking magazine subscription heads up
by Dominic Greco in Richboro PA 3/3/08, 12:52 PM
3 Replies · 24 ViewsLast post 3/3/08, 7:19 PM by Paul Kierstead -
by David Miller 3/1/08, 10:49 PM
12 Replies · 471 ViewsLast post 3/3/08, 3:56 PM by steve mackay -
by David Yoho 3/3/08, 1:22 PM
0 Replies · 27 ViewsLast post 3/3/08, 1:22 PM by David Yoho -
by Rob Lee 2/29/08, 3:42 PM
25 Replies · 110 ViewsLast post 3/3/08, 4:43 AM by Walt in Tenn. -
Here is another one I can't make out
by Stephen Shepherd in the State of Deseret 3/1/08, 10:40 PM
2 Replies · 31 ViewsLast post 3/2/08, 11:08 PM by Stephen Shepherd in the State of Deseret -
by Todd O. Cronkhite Maine Native, Presently Away 2/29/08, 3:37 PM
21 Replies · 37 ViewsLast post 3/2/08, 11:00 PM by Pam Niedermayer -
by Jim in Burlington Ont. 2/29/08, 2:01 AM
17 Replies · 48 ViewsLast post 3/2/08, 3:45 AM by Derek Cohen (in Perth, Australia) -
Rob Lee: What does '08 Hold for New Tools
by Tom Colligan 2/27/08, 2:12 AM
10 Replies · 59 ViewsLast post 3/2/08, 3:14 AM by ThomD -
by David Miller 3/1/08, 12:49 PM
3 Replies · 36 ViewsLast post 3/1/08, 7:03 PM by Scott Burr in wet windy & cold Ben Lomond, CA -
by Roy Anderson 3/1/08, 3:14 AM
0 Replies · 25 ViewsLast post 3/1/08, 3:14 AM by Roy Anderson -
by Jack Guzman from Maine 2/21/08, 11:42 PM
18 Replies · 30 ViewsLast post 3/1/08, 12:10 AM by Jack Guzman from Maine -
by Joe Rogers, Northern Virginia 2/28/08, 1:27 PM
1 Reply · 18 ViewsLast post 2/29/08, 12:52 AM by Skip in Falls Church -
by Rich Glisson 2/26/08, 9:15 PM
10 Replies · 63 ViewsLast post 2/28/08, 4:04 AM by Bill Houghton -
Wall mounted corner tool til - proof of concept
by Paul Erickson 2/26/08, 4:59 AM
18 Replies · 77 ViewsLast post 2/28/08, 4:02 AM by Bill Houghton -
by steve mackay 2/25/08, 2:52 AM
8 Replies · 27 ViewsLast post 2/27/08, 4:26 PM by Scott Burr in Ben Lomond CA -
by Tony - Memphis 2/25/08, 7:51 PM
15 Replies · 77 ViewsLast post 2/27/08, 10:17 AM by Pam Niedermayer -
Deneb Puchalski - LN Toolworks on sharpening!
by Alan DuBoff 2/25/08, 11:41 AM
11 Replies · 81 ViewsLast post 2/27/08, 10:06 AM by Alan DuBoff -
by Slav Jelesijevich 2/27/08, 5:38 AM
0 Replies · 33 ViewsLast post 2/27/08, 5:38 AM by Slav Jelesijevich -
by David Miller 2/25/08, 6:07 PM
7 Replies · 23 ViewsLast post 2/27/08, 2:19 AM by Derek Cohen (in Perth, Australia) -
A restored Stanley #45 Combo Plane
by Dominic Greco in Richboro PA 2/20/08, 3:53 AM
24 Replies · 60 ViewsLast post 2/26/08, 11:15 PM by Scott Burr in Ben Lomond CA -
Parallel vs. Tapered Single Irons in Wooden Planes
by A. Sender 2/21/08, 11:37 PM
13 Replies · 91 ViewsLast post 2/26/08, 8:17 PM by Paul Kierstead -
by Stephen Shepherd in the State of Deseret 2/26/08, 1:47 PM
0 Replies · 23 ViewsLast post 2/26/08, 1:47 PM by Stephen Shepherd in the State of Deseret -
by Brad in Ottawa 2/25/08, 9:09 PM
3 Replies · 26 ViewsLast post 2/26/08, 12:41 PM by Kevin Adams -
Why o' why did I listern to the weather man...
by Scott Burr in wet windy & cold Ben Lomond, CA 2/24/08, 11:17 PM
9 Replies · 40 ViewsLast post 2/26/08, 5:40 AM by Alan DuBoff -
by Robert Henderson 2/25/08, 3:21 PM
3 Replies · 47 ViewsLast post 2/26/08, 2:12 AM by Bruce, a MN Galoot



