General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
Riser Block for old Jet band sw
by Robert Loewenthal 3/2/19, 4:26 PM
19 Replies · 55 ViewsLast post 3/5/19, 12:04 PM by Barry Irby -
Wooden but Not Furniture *LINK*
by John McGaw 3/4/19, 3:56 PM
0 Replies · 54 ViewsLast post 3/4/19, 3:56 PM by John McGaw -
by ben d. 2/25/19, 9:04 PM
7 Replies · 56 ViewsLast post 3/4/19, 12:53 PM by Dale Stansbery -
by Roy 2/22/19, 9:13 PM
14 Replies · 51 ViewsLast post 3/4/19, 6:06 AM by CharlieL -
by Tom Norton 3/2/19, 8:02 PM
8 Replies · 36 ViewsLast post 3/4/19, 3:09 AM by Jim DeLaney, Austintown, Ohio -
by Roy 3/2/19, 9:09 PM
3 Replies · 33 ViewsLast post 3/3/19, 4:41 PM by Mark Nowicki -
Puzzzling grind on a Lee Valley Cap Iron 2
by Bill Tindall, E.TN. 2/27/19, 11:13 PM
39 Replies · 110 ViewsLast post 3/2/19, 7:51 PM by Mark Hennebury -
by Howard Pollack 3/1/19, 3:13 PM
6 Replies · 69 ViewsLast post 3/2/19, 3:25 AM by TomD -
by Jerry Gibbs 3/1/19, 12:07 PM
2 Replies · 43 ViewsLast post 3/1/19, 7:12 PM by Thomas T Dunlap -
New Arkansas stone on classified
by Bill Tindall, E.TN. 3/1/19, 2:33 PM
0 Replies · 51 ViewsLast post 3/1/19, 2:33 PM by Bill Tindall, E.TN. -
Can Solid Wood Trigger Nut Allergies?
by Don Stephan 2/28/19, 10:02 PM
3 Replies · 165 ViewsLast post 3/1/19, 12:27 PM by Barry Irby -
Cyclone dust separator Question....
by Barry Irby 2/26/19, 10:04 PM
9 Replies · 49 ViewsLast post 3/1/19, 2:34 AM by CharlieL -
by Gary Smyth 2/27/19, 2:59 AM
7 Replies · 31 ViewsLast post 3/1/19, 2:09 AM by Gary Smyth -
by Tom Norton 2/27/19, 8:14 PM
8 Replies · 58 ViewsLast post 2/28/19, 4:26 PM by Bill Howatt -
by Tom Norton 2/24/19, 1:38 PM
11 Replies · 78 ViewsLast post 2/28/19, 4:25 PM by Lee Schierer in McKean, PA -
Had to rework the saw till some
by Christopher Fitch 2/25/19, 10:25 PM
12 Replies · 74 ViewsLast post 2/28/19, 2:41 PM by Tony - Memphis -
by Barry Irby 2/24/19, 7:41 PM
10 Replies · 98 ViewsLast post 2/27/19, 10:39 PM by Bill Tindall, E.TN. -
by Bill Tindall, E.TN. 2/27/19, 2:48 PM
5 Replies · 41 ViewsLast post 2/27/19, 6:50 PM by Bill Tindall, E.TN. -
by Don Stephan 2/25/19, 11:05 PM
9 Replies · 79 ViewsLast post 2/27/19, 12:57 AM by Don Stephan -
More on Home Furniture Magazine
by Bill Tindall, E.TN. 2/26/19, 3:37 PM
0 Replies · 68 ViewsLast post 2/26/19, 3:37 PM by Bill Tindall, E.TN. -
Shot through the heart.....err...Pants.....
by Barry Irby 2/24/19, 10:36 PM
5 Replies · 35 ViewsLast post 2/25/19, 8:45 PM by Paul Blackwell -
Quickest ever jointer knife change
by Bill Tindall, E.TN. 2/24/19, 6:36 PM
4 Replies · 40 ViewsLast post 2/25/19, 1:01 PM by Larry Clinton At Frankfort, (Central) Indiana -
What would you call this screw head?
by Henry Higginbotham 2/19/19, 6:06 PM
8 Replies · 34 ViewsLast post 2/24/19, 4:09 AM by Thomas T Dunlap -
by Bill Tindall, E.TN. 2/17/19, 1:34 PM
24 Replies · 81 ViewsLast post 2/23/19, 8:43 PM by TomD -
by Dick Coers 2/20/19, 2:54 AM
6 Replies · 41 ViewsLast post 2/23/19, 8:26 PM by TomD -
Decent and Affordable Drill Bits?
by Joe Pack 2/22/19, 1:59 AM
14 Replies · 174 ViewsLast post 2/23/19, 8:19 PM by TomD -
Paper is made from wood, right? *LINK*
by John McGaw 2/22/19, 12:28 PM
5 Replies · 41 ViewsLast post 2/23/19, 8:00 PM by TomD -
North Carolina Woodturning Symposium
by Scott Hurley in N VA 2/23/19, 3:10 PM
3 Replies · 35 ViewsLast post 2/23/19, 6:24 PM by John K Jordan -
This tool cabinet photo is hilarious! *LINK*
by Dick Coers 2/18/19, 4:37 AM
22 Replies · 48 ViewsLast post 2/23/19, 12:11 AM by Derek Cohen (in Perth, Australia) -
How would you cut this piece? 2
by Bill Tindall, E.TN. 2/18/19, 10:15 PM
26 Replies · 141 ViewsLast post 2/22/19, 10:57 PM by William Duffield



