General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
Square or round...what is your favorite...
by Rob Hix - King George, VA 5/13/07, 12:17 PM
6 Replies · 59 ViewsLast post 5/13/07, 4:54 PM by Vijay -
by wudwork 5/9/07, 12:58 AM
14 Replies · 88 ViewsLast post 5/13/07, 4:01 PM by Chuck Lenz -
by David Yoho 5/13/07, 3:39 PM
0 Replies · 46 ViewsLast post 5/13/07, 3:39 PM by David Yoho -
by Robert Anderson 5/13/07, 2:35 AM
2 Replies · 38 ViewsLast post 5/13/07, 12:09 PM by Mark Mandell - Gone Round In Jersey -
Oil polyurethane varnish v. alkyd varnish?
by Sgian Dubh 5/10/07, 6:15 PM
8 Replies · 127 ViewsLast post 5/13/07, 9:20 AM by Sgian Dubh -
by Ken Grunke from SW WI 5/12/07, 2:50 PM
5 Replies · 68 ViewsLast post 5/13/07, 4:03 AM by Thad -
by Jaosn 5/10/07, 10:40 PM
7 Replies · 124 ViewsLast post 5/12/07, 2:54 PM by Joanne Adler in Pt. Pleasant, PA -
by JL 5/11/07, 4:02 PM
8 Replies · 73 ViewsLast post 5/12/07, 12:31 PM by Bill McDonnald -
by Wayne Carson 5/12/07, 2:37 AM
1 Reply · 40 ViewsLast post 5/12/07, 11:18 AM by Mark Nowicki -
by Ron Hildreth, Alta, Iowa 5/11/07, 1:28 PM
9 Replies · 48 ViewsLast post 5/12/07, 3:43 AM by Scott in Eastern Iowa -
by Dustmaker Mike 5/11/07, 11:15 AM
3 Replies · 38 ViewsLast post 5/12/07, 2:29 AM by Dan Donaldson -
OT-Funny Fake Commercial *LINK*
by Lee Gordon 5/10/07, 11:10 PM
5 Replies · 47 ViewsLast post 5/12/07, 12:41 AM by Mark Goodall - ATL - tooljunkie -
by Wayne Carson 5/10/07, 3:29 AM
4 Replies · 49 ViewsLast post 5/12/07, 12:09 AM by Michael Dresdner -
by CARL BARTON 5/11/07, 9:53 AM
1 Reply · 46 ViewsLast post 5/11/07, 11:49 PM by Curly Smith -
It seemed like a good idea at the time...
by David Sparks 5/11/07, 2:25 AM
6 Replies · 71 ViewsLast post 5/11/07, 11:04 PM by David Sparks -
by Scott in Douglassville 5/10/07, 7:02 PM
11 Replies · 75 ViewsLast post 5/11/07, 10:23 PM by Jim in Houston -
by Bob Boswood 5/8/07, 6:36 PM
10 Replies · 64 ViewsLast post 5/11/07, 8:41 PM by Jim Dillon -
Cleaning up the end grain on a raised panel
by lee beeden 5/11/07, 3:59 AM
3 Replies · 53 ViewsLast post 5/11/07, 6:30 PM by Larry Clinton At Frankfort (Central)., Indiana -
by Ray Newman 5/6/07, 9:25 PM
7 Replies · 72 ViewsLast post 5/11/07, 6:16 PM by Ray Newman -
by Carl in VA. 5/10/07, 10:32 PM
7 Replies · 85 ViewsLast post 5/11/07, 4:10 PM by Carl in VA. -
by Justin Szeliga 5/11/07, 1:54 AM
6 Replies · 56 ViewsLast post 5/11/07, 3:50 PM by Charles Sharp -
by Jeff Jewitt 5/10/07, 5:30 PM
6 Replies · 46 ViewsLast post 5/11/07, 3:10 PM by Jerry Nicholson -
by Larry in NW Ohio 5/10/07, 4:36 PM
4 Replies · 51 ViewsLast post 5/11/07, 2:16 PM by Michael Wilkins -
Any Adventurous Firefox Users? *LINK*
by Ron in Drums PA 5/10/07, 11:04 PM
3 Replies · 46 ViewsLast post 5/11/07, 12:49 PM by Curt Harms -
Leather Cushions...Black or Brown?
by Thomas Skaggs 5/10/07, 2:24 PM
17 Replies · 68 ViewsLast post 5/11/07, 12:10 PM by Keith Weber -
Squaring up to my problems....
by Rob Hix - King George, VA 5/10/07, 8:02 PM
8 Replies · 84 ViewsLast post 5/11/07, 6:22 AM by Robin Corell in Atascadero, CA -
by Ralph Chandler 5/10/07, 4:15 PM
5 Replies · 106 ViewsLast post 5/11/07, 5:42 AM by Chuck Lenz -
by ernie miller 5/10/07, 12:39 AM
3 Replies · 48 ViewsLast post 5/11/07, 4:17 AM by Jim Moore -
by Thomas Skaggs 5/9/07, 6:39 PM
8 Replies · 60 ViewsLast post 5/10/07, 10:58 PM by Jim Shaver - Oakville, Ontario -
Square the hole or round the peg?
by Gary Evans Tallassee, TN 5/10/07, 2:55 PM
2 Replies · 55 ViewsLast post 5/10/07, 9:11 PM by Gary Evans Tallassee, TN



