General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
under sink cut-off valve question
by Bill Tindall, E.TN. 1/29/20, 7:42 PM
19 Replies · 61 ViewsLast post 2/2/20, 9:11 PM by Johanna Johanson -
Entry hall table for a niece: Part 5
by Derek Cohen (in Perth, Australia) 2/1/20, 4:30 PM
8 Replies · 176 ViewsLast post 2/2/20, 8:22 PM by Bill Tindall, E.TN. -
by Barry Irby 1/30/20, 2:08 PM
10 Replies · 41 ViewsLast post 1/31/20, 12:10 AM by Keith Newton -
by JL 1/29/20, 9:09 PM
4 Replies · 38 ViewsLast post 1/30/20, 5:26 PM by Tom Dunlap -
I just sharpened a card scraper
by Bill Tindall, E.TN. 1/29/20, 1:01 AM
16 Replies · 53 ViewsLast post 1/30/20, 4:39 PM by Bill Tindall, E.TN. -
Kencraft Toledo Ohio? Dust collection pipe
by Michael van pelt 1/27/20, 7:46 PM
5 Replies · 39 ViewsLast post 1/30/20, 1:04 PM by Brad Chenoweth -
Wooden chair question/ shape of back
by Barry Irby 1/28/20, 1:47 PM
4 Replies · 50 ViewsLast post 1/29/20, 6:47 PM by jessecloud -
For the Kitchen Cabinet Makers
by howgor 1/28/20, 9:55 PM
8 Replies · 30 ViewsLast post 1/29/20, 1:24 PM by howgor -
Replacing Dust Collector Filter Bag with Cannister
by mark 1/26/20, 10:56 PM
8 Replies · 147 ViewsLast post 1/29/20, 12:15 PM by Mark -
by Larry verhff 1/28/20, 6:40 PM
3 Replies · 36 ViewsLast post 1/29/20, 1:22 AM by Bruce, a MN Galoot -
by Gary Smyth 1/28/20, 3:25 AM
7 Replies · 34 ViewsLast post 1/29/20, 1:17 AM by Gary Smyth -
by JL 1/26/20, 4:13 PM
6 Replies · 92 ViewsLast post 1/28/20, 11:16 PM by Bill Tindall, E.TN. -
Looking for switch to turn on vacuum with air tool
by Stephen Roth 1/27/20, 8:47 PM
3 Replies · 54 ViewsLast post 1/28/20, 6:54 PM by Larry verhff -
by Michael van pelt 1/27/20, 7:51 PM
4 Replies · 58 ViewsLast post 1/28/20, 3:31 PM by Michael van pelt -
by Tom Norton 1/26/20, 1:47 PM
14 Replies · 79 ViewsLast post 1/28/20, 2:11 PM by GolfSteve in Calgary -
by Yonak 1/26/20, 2:22 AM
26 Replies · 159 ViewsLast post 1/28/20, 3:28 AM by Yonak -
Question on prefinished UV plywood
by Tim Greif - West of Chicago 1/26/20, 7:36 PM
11 Replies · 78 ViewsLast post 1/28/20, 12:29 AM by Dave Bair -
by Michael Farinella 1/27/20, 3:32 PM
0 Replies · 51 ViewsLast post 1/27/20, 3:32 PM by Michael Farinella -
so I made a platen for my Dewalt Planer...
by Barry Irby 1/25/20, 6:41 PM
6 Replies · 52 ViewsLast post 1/26/20, 6:31 PM by Barry Irby -
Drill Press work anchor question...
by Barry Irby 1/26/20, 1:22 PM
2 Replies · 30 ViewsLast post 1/26/20, 5:55 PM by Barry Irby -
Entry hall table for a niece: Part 4
by Derek Cohen (in Perth, Australia) 1/25/20, 3:47 PM
8 Replies · 216 ViewsLast post 1/26/20, 3:51 PM by Derek Cohen (in Perth, Australia) -
A chair is never just a chair: CBC Radio.
by mark nowicki 1/26/20, 2:57 PM
0 Replies · 51 ViewsLast post 1/26/20, 2:57 PM by mark nowicki -
by Stuart Johnson 1/25/20, 7:50 PM
6 Replies · 64 ViewsLast post 1/26/20, 12:17 AM by Mark Mandell -
by Bill Tindall, E.TN. 1/25/20, 9:49 PM
0 Replies · 80 ViewsLast post 1/25/20, 9:49 PM by Bill Tindall, E.TN. -
Adjusting drawer side fit......
by roger lance 1/20/20, 8:33 PM
15 Replies · 133 ViewsLast post 1/25/20, 9:24 PM by roger lance -
by Ray Carson - Lawrenceville, NJ 1/22/20, 2:53 PM
1 Reply · 29 ViewsLast post 1/25/20, 8:09 PM by Ellis Walentine -
by John K Jordan 1/24/20, 7:58 PM
8 Replies · 68 ViewsLast post 1/25/20, 7:25 PM by John K Jordan -
Entry hall table for a niece: Part 3
by Derek Cohen (in Perth, Australia) 1/22/20, 5:52 PM
13 Replies · 223 ViewsLast post 1/25/20, 2:49 PM by Derek Cohen (in Perth, Australia) -
by Michael van pelt 1/24/20, 1:35 PM
13 Replies · 62 ViewsLast post 1/25/20, 1:58 PM by Barry Irby -
small coves and a splitter in a pinch
by Bill Tindall, E.TN. 1/24/20, 8:10 PM
1 Reply · 27 ViewsLast post 1/24/20, 8:35 PM by Yonak