General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
by Rod Peterson -- Ormond Beach 4/3/09, 3:18 AM
4 Replies · 61 ViewsLast post 4/4/09, 6:57 AM by Tom Dunlap -
by Dan Donaldson 4/1/09, 9:40 PM
4 Replies · 18 ViewsLast post 4/4/09, 4:02 AM by Dan Donaldson -
by David Hammelef 3/31/09, 11:14 PM
9 Replies · 29 ViewsLast post 4/4/09, 2:06 AM by David Hammelef -
Carving tool sharpening info needed
by Joe Pack 4/2/09, 4:19 AM
12 Replies · 65 ViewsLast post 4/3/09, 11:00 PM by Jim Dillon -
Has anyone made a futon using the Rockler plans?
by Bruce, a MN Galoot 4/1/09, 6:35 PM
3 Replies · 19 ViewsLast post 4/3/09, 11:00 PM by JimG------WebKitFormBoundaryAA2hAApkAA+UAAXL -
O.T.: Mortgage rates will soon drop...
by David Sparks 4/3/09, 5:24 PM
3 Replies · 52 ViewsLast post 4/3/09, 8:47 PM by JL -
Sharing birthday with Jim Shaver.....
by Jesper, Denmark 4/2/09, 6:01 AM
6 Replies · 17 ViewsLast post 4/3/09, 8:29 PM by HC Sakman will WALK IN LeeValley APRIL 13.!!!! -
by John Veerkamp,Western Mo 4/3/09, 2:04 AM
9 Replies · 21 ViewsLast post 4/3/09, 5:12 PM by Howard Norman -
by Steve Strickland 3/31/09, 9:51 PM
3 Replies · 16 ViewsLast post 4/3/09, 1:15 PM by Lee Grindinger -
Lower Cost Slow Speed Sharpening
by howard 4/2/09, 1:21 PM
7 Replies · 44 ViewsLast post 4/3/09, 1:01 PM by howard -
OT Who says Fargo doesn't have a beach? *LINK*
by Alan Young 4/2/09, 7:57 PM
2 Replies · 13 ViewsLast post 4/3/09, 12:24 PM by Jake Dahn (SoMN) -
shellac finish on 1/8-inch birch ply question*pic*
by Dale Sherman 3/31/09, 2:02 AM
7 Replies · 44 ViewsLast post 4/3/09, 3:30 AM by Dale Sherman -
Plans for a tablesaw mobile work station?
by Chris Knob 4/1/09, 4:50 PM
5 Replies · 27 ViewsLast post 4/3/09, 1:37 AM by M. McNamee -
26 Replies · 83 ViewsLast post 4/3/09, 12:30 AM by Gary Evans Tallassee, TN
-
by steve mackay 4/2/09, 9:59 PM
0 Replies · 14 ViewsLast post 4/2/09, 9:59 PM by steve mackay -
by Al Stokka 3/31/09, 8:22 AM
19 Replies · 33 ViewsLast post 4/2/09, 8:01 PM by Jim Shaver - Oakville, Ont -
by paul womack 4/1/09, 12:19 PM
17 Replies · 126 ViewsLast post 4/2/09, 7:32 PM by GolfSteve in Calgary -
A Clearance Deal at Canadian Tire
by Bricofleur 4/2/09, 7:13 PM
0 Replies · 16 ViewsLast post 4/2/09, 7:13 PM by Bricofleur -
OT:Source for HP 5000N WinXP 64bit drivers?
by Dominic in Bucks County PA 4/1/09, 5:36 PM
6 Replies · 29 ViewsLast post 4/2/09, 3:44 PM by Jerry Nicholson -
by Brian in Brighton 4/1/09, 2:19 AM
10 Replies · 33 ViewsLast post 4/2/09, 2:31 PM by Brian in Brighton -
by John K Jordan 3/30/09, 2:02 AM
12 Replies · 59 ViewsLast post 4/2/09, 1:24 PM by John K Jordan -
by Dan Donaldson 4/1/09, 2:20 PM
5 Replies · 19 ViewsLast post 4/2/09, 11:47 AM by Rob Lee -
by David Yoho 4/1/09, 10:07 PM
1 Reply · 13 ViewsLast post 4/2/09, 8:36 AM by Chris Knob -
OT Spit on your finger, Am I the only one???
by Barry Irby 4/1/09, 11:47 AM
9 Replies · 22 ViewsLast post 4/2/09, 1:51 AM by steve mackay -
by Woodie49 3/30/09, 11:10 PM
8 Replies · 35 ViewsLast post 4/2/09, 1:14 AM by GalenV in Iowa -
Two questions about Oak plywood
by Bernard 3/31/09, 8:06 PM
11 Replies · 32 ViewsLast post 4/2/09, 12:39 AM by Pete in Holland, MI -
by Larry in NW Ohio 4/1/09, 10:55 PM
0 Replies · 17 ViewsLast post 4/1/09, 10:55 PM by Larry in NW Ohio -
by Dustmaker Mike 4/1/09, 10:25 AM
5 Replies · 15 ViewsLast post 4/1/09, 5:14 PM by Dustmaker Mike -
by Ed F. 3/30/09, 3:25 AM
12 Replies · 26 ViewsLast post 4/1/09, 4:58 PM by Glenn Madsen near San Francisco -
WC Weekend Accomplishments....
by Dennis E Peacock 3/30/09, 12:46 PM
12 Replies · 62 ViewsLast post 4/1/09, 4:34 AM by Hank Knight



