Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Wood rack design comments

Posts

Wood rack design comments

#1

Wood rack design comments

David Hammelef

>Ok, thanks for all the input earlier. Took some of those designs, with a few others I found and have started on a rack...

2x4 arms, the supports will be 2x4 sandwiched between 1/2" ply. (cut about 1/8" narrow than the 2x4 so about 3 3/8") the ply will stop about 5" from the bottom, and extend 5" above to grab the floor truss. Center section 2x4 are about 10" long with a 2 deg angle in them.

All the wood is cut, the question is how to assemble. Original thought put down ply, glue 2x4 put down and screw. But I think I want the screws coming in from the ply side. Also should I glue and screw in the arms, or leave them free floating so I can remove if I need more height than 10".

Im tired, and maybe making to big a deal out of this. Maybe I just lay the 2x4 down (including arms to keep spacing correct) and glue and screw just the leg parts. Can use clamps to keep the 2x4s straight I think. Any thoughts????

Something like this (See pic) but mine will go to the floor, and is using thicker ply.


img

Re: Wood rack design comments

#2

Re: Wood rack design comments

David Hammelef

>Oh this pic looks very close to what I am trying except they used 2x4's in all layers. My "bread" in this sandwich is 1/2" ply.

Boy there arms are long. How long can I go safely?


img

Re: Wood rack design comments

#3

A couple of thoughts

Barry Irby

>You mentioned floor trusses. Are they the wooded I beam type with the thin plywood/OSB web? Is the bottom flange actually a 1 1/2" wide member that will match up with a 2x4's thickness? Most of them I have seen are not 1 1/2". Another concern with that type of truss is you should not hang anything heavy off the bottom cord. Could pull the cord off the truss. Resting the rack on the floor would probably solve that problem. And, if yours are truly trusses, 2x4's turned flat, forget I mentioned it.

I have a rack in my shed that was built along side the studs. Sort of the Stud/block/stud sandwich shown in one of your pics that has arms about 18" long and they have been full of lumber for over twenty years and have not sagged. I have another that I built when I was a kid that is just pieces about 12" long nailed on the side of 2x4's and they are working fine.

In your design, I think the plywood is the limiting factor. Only the long vertical plus really count in this application. The horizontal ones add very little. A 1x4 (or 2x4) would have been much stronger. Have not done any calculation and really don't know how anymore, but I am a little skeptical of the plywood in the long run. My gut tells me that if you had used 1x4's on each side and glued and nailed everything, you could break the 2x4 arms before the rack would fail.

As for assembly, I would lay it out on the floor and nail (and glue) the blocks to the bottom piece of ply with nails that did not protrude out the other side. Then I would glue and nail on the top piece of ply, turn it over and nail the first side. Might make a template or pattern to keep them identical. I might even stretch a string on the tips when I put them up. If they are not in a straight line, your lumber will conform to the rack and become crooked.

Why the plywood? wouldn't 2x4's have been cheaper?

Re: Wood rack design comments

#4

Over kill!

Bill Tindall, E.TN

>Do I understand that you intend the horizontal supports to be 2- 2x4 plus a plywood stiffener? For this tiny span a single 2 x 4 is more than adequate.

The rack shown in the picture is made from double vertical 2 x 4's and single horizontal 2 x 4's (yellow pine) with a 4' span between verticals (yellow pine) and a spacing between units of 4'. The units are bolted together with 2- 1/4" carriage bolts per lumber intersection. We have used this arrangement for more than 30 years to store lumber. Each bay holds about 1000 bd ft of 12' lumber.

Once dry, hardwood lumber is very stiff. A 4' spacing between supports is adequate, except you might want more supports for short stuff.


img

Re: Wood rack design comments

#5

Scraps

David Hammelef

>All of this is being done with wood laying around. Figured better to use up what I have then buy more. I think the ply on the side is more to keep things in line, The load should be carried through the 2x4 sections.

Re: Wood rack design comments

#6

Re: Over kill!

David Hammelef

>Nope, Guess I was not clear. Look at my sencond post. The horizontal arms will just be a 2x4 of yet to be determined lenght, was think 14" (so 10.5" sticking out) but maybe I can go longer. Will have to inventory the pile to see what I have.

The ply wood, 2x4,plywood sandwich is for the vertical supports.

Re: Wood rack design comments

#7

Over kill there too

Bill Tindall, E.TN

>My 2-2 x 4 verticals hold several thousand bd ft of lumber just fine. In the picture 9 verticals are holding up more than 5 tons of lumber. If you simply bolt your horizontal pieces between 2- 2 x4's there will be plenty of strength. For your short horizontal pieces just one vertical 2 x 4 would be plenty. 15- 2x4's in a basement wall hold up the entire center of my two story house (house is framed with floor joists running parallel to length of house, not across as it common).

The weakest point in your arrangement is how the verticals are fastened to the wall.

Re: Wood rack design comments

#8

Re: Over kill there too

Barry Irby

>Bill is right. I thought the arms were going to cantilever two feet, not ten inches. The rack will be plenty strong.

Re: Wood rack design comments

#9

Re: Wood rack design comments

Brian in Brighton

>I would go with 2x2 arms since they are so short. It would give you half of the lost shelving due to the braces. If you go more than 18 inches long arms than I would use 2x4 and cut them to a 2x2 taper at the tips. Figure if you can hang on the arm ends than you should have no problem. Mounting the vertical supports to touch the floor is a good idea for the weight distribution to the floor instead of all on the wall.

Brian in Brighton

Re: Wood rack design comments

#10

Re: Over kill there too

David Hammelef

>Glad to hear the number of verticals is sufficient if no excessive. Since they are 2' apart I still want to use 6 to be able to support short, medium, or longer lengths of lumber.

Gotta see how far out they can stick out that will still work, and see what scraps I have to see if I can have the arms go out further.