Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

shellac finish on 1/8-inch birch ply question*pic*

Posts

shellac finish on 1/8-inch birch ply question*pic*

#1

shellac finish on 1/8-inch birch ply question*pic*

Dale Sherman, Manlius, NY

>I make laser cut model houses out of 1/8" Baltic Birch for energy education instructors. I was using a lacquer finish before they go to the laser and, while it was the best contrast, they went together well. I tried using clear shellac to get better contrast with the laser engraving, but the panels appear to cup towards the finish.

Could the shellac cause the wood on the finished side to shrink slightly? Does the alcohol draw water from the wood when it evaporates? Why does the wood warp as if the shellac is shrinking the surface?

This pic shows a model house with lacquer finish and no warping.


Been a long time since I posted or even lurked. Nice to be back.

Dale

Re: shellac finish on 1/8-inch birch ply question*pic*

#2

typo: lacquer WASN'T the best contrast

Dale Sherman, Manlius, NY

>

Re: shellac finish on 1/8-inch birch ply question*pic*

#3

Re: typo: lacquer WASN'T the best contrast

Fred Davis

>shellac both sides of the plywood and the problem will go away.

FredD

Re: shellac finish on 1/8-inch birch ply question*pic*

#4

Re: shellac both sides

Dale Sherman, Manlius, NY

>I tried that and it appears to help. I have to mask off the areas that get glue, though. I usually shellac the whole sheet, then get it laser cut it which makes it hard to know where to mask on the back side.

I thought it might be moisture absorption from the back, but this happens with stabilized wood and happens shortly after finishing. Doesn't happen with lacquer. Perhaps I'd get better laser contrast if I used something other than acrylic lacquer?

Dale

Re: shellac finish on 1/8-inch birch ply question*pic*

#5

Hi Dale -- some speculation for you

Ellis Walentine, Host

>I suspect that Fred's advice to shellac both sides of the plywood will leave your panels flat, but I'm unclear as to the exact mechanism that causes the cupping you described. I imagine it is akin to the unbalanced moisture transfer that you get when you veneer only one side of a plywood panel, though in that case it may also have to do with shrinkage of the veneer and/or the glue line. In your case, the shellac film itself must shrink slightly as the solvent evaporates. It doesn't take much dimensional change to cause a rather dramatic cup.

Why this doesn't happen with lacquer is a mystery, though, unless lacquer doesn't have the shrinkage coefficient of shellac. It could also have to do with ambient relative humidity at the time you finished the panels. If the back side of the panel is exposed to the air, and the air is relatively moist, it would cause the unprotected side to expand, cupping the finished side.

How's that for a bunch of non-answers. Maybe Mike Dresdner has some insights.

Ellis

Re: shellac finish on 1/8-inch birch ply question*pic*

#6

Re: shellac finish on 1/8-inch birch ply question*

Ken Krawford

>Dale,

I wonder if adding just a drop or 2 of a dye like Trans Tint to the lacquer would improve the contrast?

Just a thought.

Re: shellac finish on 1/8-inch birch ply question*pic*

#7

contrast

Bill Tindall, E.TN

>I am not sure what you mean by contrast. Shellac can be yellow to orange. Acrylic polymers(finishes) are water white. Is this the contrast you are seeing? If so use nitrocellulose lacquer and it will near exactly match shellac.

I would like to say that the shellac film is shrinking as it dries as the cause of the bowing but I have no theory to explain why it should compared to the acrylic. .

Re: shellac finish on 1/8-inch birch ply question*pic*

#8

Re: Hi Dale -- some speculation for you

Dale Sherman, Manlius, NY

>That pretty much matches all of my speculation. Warping happens a couple days after finishing. Never goes away. I have pieces laying around with both lacquer and shellac. The shellac piece is warped, the lacquer piece is fine. Been that way since last fall. Perhaps the alcohol is causing some cell shrinkage? Hopefully MD has an answer.

Dale