Hand Tools
Traditional tools, sharpening, restoration, usage techniques.
Related: Hand Tools archive
Topic list
-
TopicStatisticsLast post
-
by Bob Smalser, Seabeck, WA 3/29/04, 4:26 AM
3 Replies · 73 ViewsLast post 3/29/04, 1:36 PM by Bob Smalser, Seabeck, WA -
by David Yoho 3/29/04, 1:05 PM
0 Replies · 82 ViewsLast post 3/29/04, 1:05 PM by David Yoho -
by tom in AR 3/28/04, 7:10 AM
14 Replies · 150 ViewsLast post 3/29/04, 2:42 AM by Todd O. Cronkhite Native of Maine -
Project Pics - Crystal Display Case w/ long story
by GolfSteve in Calgary 3/24/04, 6:35 AM
8 Replies · 80 ViewsLast post 3/29/04, 2:25 AM by GolfSteve in Calgary -
Six-board chest - Progress *Pics*
by Scott in Douglassville, PA 3/27/04, 6:30 PM
2 Replies · 59 ViewsLast post 3/29/04, 1:56 AM by Martin, from Granbury -
by Maurice 3/28/04, 10:52 PM
0 Replies · 91 ViewsLast post 3/28/04, 10:52 PM by Maurice -
by Steve 3/27/04, 7:42 PM
5 Replies · 113 ViewsLast post 3/28/04, 6:52 PM by Bill Tindall, E. TN -
LF : Opinions on Two Cherries mortise chisels
by Stephen in Ottawa 3/24/04, 11:13 PM
11 Replies · 138 ViewsLast post 3/28/04, 6:16 PM by Lyn J. Mangiameli -
Swan neck mortise chisel question
by Sandor in Boyds, MD 3/25/04, 5:41 PM
13 Replies · 103 ViewsLast post 3/28/04, 5:20 PM by Don Thompson, Cutler Ridge, South of Miami FL -
by Dan Donaldson 3/27/04, 5:04 PM
4 Replies · 90 ViewsLast post 3/28/04, 5:45 AM by William Duffield on the Cohansey -
by Jeff Spirer 3/26/04, 2:36 PM
4 Replies · 83 ViewsLast post 3/28/04, 5:37 AM by William Duffield on the Cohansey -
Flexner's finishing book on benefit auction.
by Dale Stansbery 3/28/04, 4:58 AM
0 Replies · 114 ViewsLast post 3/28/04, 4:58 AM by Dale Stansbery -
by Scott Post 3/27/04, 2:19 PM
8 Replies · 103 ViewsLast post 3/28/04, 4:16 AM by Bill Tindall, E. TN -
by Dan Donaldson 3/27/04, 2:51 AM
3 Replies · 137 ViewsLast post 3/27/04, 4:29 PM by Dan Donaldson -
by Moses Yoder in White Pigeon, MI 3/27/04, 1:49 AM
3 Replies · 72 ViewsLast post 3/27/04, 3:07 PM by Greg Betit, Crown Point NY -
by Garrett in Victoria BC CA 3/25/04, 5:06 AM
13 Replies · 72 ViewsLast post 3/27/04, 12:04 PM by Jack from Maine -
by Matt in Iowa 3/25/04, 8:08 PM
2 Replies · 65 ViewsLast post 3/27/04, 3:27 AM by Lloyd Robins -
by Jay Hanks/ Columbus Ohio 3/25/04, 11:52 PM
9 Replies · 98 ViewsLast post 3/27/04, 1:44 AM by Adam Cherubini, NJ -
by Garrett in Victoria BC CA 3/26/04, 4:22 PM
4 Replies · 69 ViewsLast post 3/27/04, 12:22 AM by Scott Burr in Ben Lomond CA -
by janderr 3/26/04, 11:25 PM
2 Replies · 72 ViewsLast post 3/27/04, 12:22 AM by David Barnett -
by sweetchuck 3/26/04, 5:14 PM
5 Replies · 169 ViewsLast post 3/27/04, 12:13 AM by Garrett in Victoria BC CA -
by R.J.Whelan 3/24/04, 10:38 PM
13 Replies · 72 ViewsLast post 3/26/04, 11:44 PM by Jack from Maine -
by Bob Hutchins in Central TX 3/24/04, 5:09 AM
6 Replies · 72 ViewsLast post 3/26/04, 11:02 PM by Bob Hutchins in Central TX -
by Ernie Miller 3/26/04, 2:58 PM
2 Replies · 112 ViewsLast post 3/26/04, 8:29 PM by David Linnabary -
woodworking school online! *LINK*
by George D. Huron 3/23/04, 5:53 PM
7 Replies · 74 ViewsLast post 3/26/04, 8:15 PM by Andrew F -
Panels cupping now - problem or not?
by Scott in Douglassville, PA 3/26/04, 8:13 PM
0 Replies · 121 ViewsLast post 3/26/04, 8:13 PM by Scott in Douglassville, PA -
by Matt Berry in MI 3/26/04, 2:15 PM
4 Replies · 84 ViewsLast post 3/26/04, 7:08 PM by Matt Berry in MI -
by Ernie Miller 3/26/04, 3:19 PM
5 Replies · 80 ViewsLast post 3/26/04, 6:00 PM by Ernie Miller -
by Ernie Miller 3/25/04, 8:25 PM
7 Replies · 82 ViewsLast post 3/26/04, 5:40 PM by Mike L. in SoCal -
by Scott in Douglassville, PA 3/25/04, 4:35 PM
8 Replies · 443 ViewsLast post 3/26/04, 5:09 PM by Scott Burr in Ben Lomond CA



