General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
horizontal boring machine set up
by Ken Kimura 8/27/07, 1:08 AM
2 Replies · 49 ViewsLast post 8/27/07, 1:59 PM by Ken Kimura -
by Samuel Brooks 8/25/07, 4:46 PM
1 Reply · 36 ViewsLast post 8/27/07, 1:44 PM by Tony - Memphis -
by Ray Thompson - Middletown,IN 8/27/07, 12:35 AM
2 Replies · 33 ViewsLast post 8/27/07, 9:07 AM by Dustmaker Mike -
by Dustmaker Mike 8/24/07, 10:44 AM
5 Replies · 39 ViewsLast post 8/27/07, 5:07 AM by DB -
by mike kula 8/27/07, 12:40 AM
1 Reply · 98 ViewsLast post 8/27/07, 4:42 AM by Forrest Addy -
Warning: Don't let this happen to you.
by marc rosen 8/26/07, 10:18 PM
2 Replies · 27 ViewsLast post 8/27/07, 12:00 AM by john lucas -
by sean Troy 8/26/07, 4:38 PM
2 Replies · 35 ViewsLast post 8/26/07, 11:07 PM by Jim Dillon -
by JL 8/26/07, 8:52 PM
4 Replies · 160 ViewsLast post 8/26/07, 11:03 PM by Jesse in New Mexico -
by Ron Hildreth, Alta, Iowa 8/25/07, 4:38 PM
9 Replies · 48 ViewsLast post 8/26/07, 6:31 PM by Jim Shaver - Oakville, Ontario -
NEW Shop Shots - Shop Related!
by David Yoho 8/26/07, 5:16 PM
0 Replies · 30 ViewsLast post 8/26/07, 5:16 PM by David Yoho -
by Barry Irby 8/24/07, 11:19 PM
11 Replies · 66 ViewsLast post 8/26/07, 4:35 PM by Larry Clinton At Frankfort (Central)., Indiana -
by Mike Hamilton 8/24/07, 11:34 PM
10 Replies · 79 ViewsLast post 8/26/07, 4:22 PM by Mike Hamilton -
by Robert R Clough - Thorncraft 8/25/07, 12:38 PM
2 Replies · 29 ViewsLast post 8/26/07, 3:06 PM by Derek -
Delta DC-380 planer stripped gears
by Paul Pestock 8/26/07, 2:34 AM
2 Replies · 40 ViewsLast post 8/26/07, 12:16 PM by Chuck W -
Good deal on Ebay so far... *LINK*
by David G. Sparks 8/25/07, 1:05 PM
1 Reply · 31 ViewsLast post 8/26/07, 12:01 PM by ebd -
by Bill Tindall, E.TN. 8/25/07, 1:27 PM
6 Replies · 53 ViewsLast post 8/26/07, 10:24 AM by Mark Nowicki -
Informal Survey: how many straight bits have you?
by Bill Hylton 8/23/07, 5:24 PM
17 Replies · 97 ViewsLast post 8/26/07, 3:02 AM by HC Sakman -
Finished a project! LF Camera Back
by Scott in Douglassville, PA 8/23/07, 10:21 PM
14 Replies · 143 ViewsLast post 8/25/07, 11:28 PM by Ed Snow -
by Joshua 8/23/07, 10:14 PM
6 Replies · 146 ViewsLast post 8/25/07, 11:05 PM by Jim Shaver - Oakville, Ontario -
Qujestion on Sharpening devices 2
by Robert R Clough - Thorncraft 8/23/07, 12:02 AM
27 Replies · 135 ViewsLast post 8/25/07, 10:43 PM by Derek -
by Matt Robinette,Mt Juliet Tn 8/25/07, 6:18 PM
2 Replies · 35 ViewsLast post 8/25/07, 9:24 PM by George -
Tool/assembly table on Craigslist *LINK*
by Andy Lincoln 8/25/07, 8:07 PM
0 Replies · 30 ViewsLast post 8/25/07, 8:07 PM by Andy Lincoln -
Insulation opinions wanted - OT
by Dan Manturi 8/24/07, 2:12 AM
23 Replies · 141 ViewsLast post 8/25/07, 7:11 PM by Mark Nowicki -
OT Any ideas how to cut off a ring from a finger? 2
by Ron in Drums PA 8/23/07, 2:07 PM
31 Replies · 141 ViewsLast post 8/25/07, 4:14 PM by Ronald Walls -
Looking for a good sharpening service
by Dave Anderson (PacNW) 8/24/07, 11:55 PM
8 Replies · 45 ViewsLast post 8/25/07, 3:16 PM by George -
What is your greatest accomplishment? 2
by Katie 8/23/07, 3:10 PM
28 Replies · 138 ViewsLast post 8/25/07, 12:39 PM by Ian (in Sydney, Australia) -
by stew 8/24/07, 3:15 AM
9 Replies · 80 ViewsLast post 8/25/07, 11:37 AM by Ellis Walentine -
Penn State Ind. 4" hoses? *LINK*
by JL 8/23/07, 3:06 PM
4 Replies · 46 ViewsLast post 8/25/07, 11:30 AM by Bartee (metro Atlanta) -
by Larry Clinton At Frankfort (Central)., Indiana 8/24/07, 5:44 PM
5 Replies · 104 ViewsLast post 8/25/07, 12:40 AM by Larry Clinton At Frankfort (Central)., Indiana -
Off topic: What about them O's?
by marc rosen 8/23/07, 1:22 AM
4 Replies · 42 ViewsLast post 8/24/07, 11:46 PM by Doug Ball



