Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Router Table/Lift Questions

Posts

Router Table/Lift Questions

#1

Router Table/Lift Questions

Barry Irby

>Have been refurbishing my TS. It has a wing on it with a home made router insert in it.

The question is whether to upgrade or not?

What type of router plate lift gizmo do you have or what would you buy if you could do it over?

What is there to know? Is a top side adjustment important? What about dust pick up? Changing bits? Power supply? switch? What router do you use or what must you have?

Any tips or input would be appreciated.

Re: Router Table/Lift Questions

#2

JL

Re: Router Table/Lift Questions

JL

>"Is a top side adjustment important?" I really like having one. It makes adjusting things a lot easier than reaching under the tabletop to adjust things.

"What about dust pick up?" Definitely necessary. I have had a top side (in the fence) dust pick up for a while. I am now enclosing the underside of the table with a dust port so I can pick up the dust from there.

"Changing bits?" I like being able to change the bits from the top side. Again, it makes thing easier.

"Power supply? switch?" I am debating on buying one. Eventually I will.

"What router do you use or what must you have?" I've got a PC 890 series in my table. I'd like a more powerful PC or Triton.

I haven't really found it necessary to go for a separate lift mechanism yet. But I don't do that much with my router in the table.

Re: Router Table/Lift Questions

#3

Re: Router Table/Lift Questions

Larry Clinton At Frankfort (Central)., Indiana

>I built my router table with a hinged top. I have a big PC 7539 Speedmatic plunge router. I used a Rockler plate with a "Router Raizer". I would say you definitely want an above table height adjustment. I do quite a few repeat moldings, panel raising, etc. Sometimes I have to "tweak" the height setting several times to duplicate existing finished material. I don't have the above table bit change option, it would be nice but I can raise my top (have a Lee Valley ratchet mechanism that holds it open) to loosen the collet. One thing - if you are going to raise panels or run large diameter bits you really do need variable speed - and a large router. I like and would recommend the PC series, but many have left good reports on several brands. Ellis did a study on table routers and router lifts a year or so ago, might pay to search the message archives.

Re: Router Table/Lift Questions

#4

Re: Router Table/Lift Questions

Sean Troy

>Along those same lines, what do you all use for a fence on the TS Router setups? thanks, Sean

Re: Router Table/Lift Questions

#5

Re: Router Table/Lift Questions

del schisler

>the best table and dust collection I have this table and 5 routers PC690 and 3 router tables I dont use any adjusting from the top Once you see this table You know why it is just easy to adjust when the router and plate are out of the table http://us.oak-park.com/catalogue.html?list=RT01-- their are lot's of items Just click around del

Re: Router Table/Lift Questions

#6

Re: Router Table/Lift Questions / Table saw ?

Dan manturi

>This is a good thread. I'd like to add a question - I have a stand alone router table and was thinking of moving to a table saw side table to save space. How many use the separate router table / views on using table saw side table as router table welcome. I guess dust collection is better with a stand alone table with a port in the back.

Dan M

Re: Router Table/Lift Questions

#7

Re: Router Table/Lift Questions / Table saw ?

George@Colonel's Workshop-Havertown PA

>Good Afternoon Dan,

I'm on my 2nd home-built router table, fairly similar to Norm's. I have a Rousseau plate bored to receive both P+C 690 and P+C 7518 machines. In a very small shop it makes sence to me to have the router slung below the table saw wing. My shop is not so small that I am compelled to marry table saw and router. The table has advantages except for space reduction. I have more than ample storage for all my bits, collets, collars, spare bearings and other important do-dads. I also have storage for several other plunge and standard routers and my laminate trimmer-----all within the table's cabinet or below it. Further, I can use a commercial fence designed for router use. I've not ever liked the idea of using my table saw fence with a router: It sits too low for feather boards and is not split for dust collection thru a fence port. DC happens also from the cabinet's interior, and its fairly effective, but much better thru the fence port. I feel the argument for a stand alone table, sized appropriately, is the strongest. However, to each his own. I don't use a lift. I'd like to have one. Prices are too high and I am familiar enough with setting up my machines that I can do without.

George

Re: Router Table/Lift Questions

#8

Re: Router Table/Lift Questions / Table saw ?

Dan manturi

>Thanks for that info. I have a 20 x 22 garage where a car parks on one side and my tools are on the other. The car side is usable as needed, and even no problem to tie it up for a couple of days making a larger project, but I am trying to conserve space and the router table I bae is maybe 36 x 27. The cabinet does have storage. Guess rather than chucking the table I'll just try to be more creative about consolidating all my router stuff in that cabinet. Everything is on wheels and sometimes it is just a pain to roll all the stuff out and back..

Thanks for the insight.

Dan M

Re: Router Table/Lift Questions

#9

Re: Router Table/Lift Questions

John Ballance

>I have a Woodpecker PRL mounted in the right extension table, with a PC 7518 router mounted in. This setup allows above table height adjustment, and above table bit changing (using offset wrenches). I've built a dust-collecting box around the router, tied to a dust port on the back. I added a Rockler router switch under the rip fence rail, so I can turn the router on and off without crawling on my knees. I brought power to a set of plugs mounted under the back of the table saw. The router switch and mobile dust collector plug in there, along with the table saw. This works since I never operate the table saw and router at the same.

I use an Incra Twin-Linear fence mounted to the right end of the extension table, so I can get it completely out of the way if needed to use the full table saw extension. I could also use the table saw fence for a router fence in a pinch. The entire setup works great, and I find that I use the router table far more often than a hand-held router because it's always available.

Is a lift essential? -- not really -- but it sure is convenient.

Good luck.

Re: Router Table/Lift Questions

#10

Speaking of on/off switches

Ray Newman

>One of the "accessories" that I added to my table-mounted PC 7518 router is a magnetic starter/switch from Grizzly.

Where I live, it is not unusual to have power failures -- either extended or momentary. I purchased the switch as there was a power failure while I was using the router, then it started up again as I was removing the stock. The second such incident in about a 10 minute span made me stop & think 'bout a remedy....

http://www.grizzly.com/catalog/2007/Main/231

Re: Router Table/Lift Questions

#11

Re: Router Table/Lift Questions

Larry Clinton At Frankfort (Central)., Indiana

>I ran into a real deal at an auction about 4 years ago (a year before I built my router table). I purchased a Bench Dog Pro fence 36, for a router table new in the box for, as I recall $30. It has really worked well for me. They are about $130 retail however.

Re: Router Table/Lift Questions

#12

Re: Router Table/Lift Questions / Table saw ?

Larry Clinton At Frankfort (Central)., Indiana

>I have to agree Colonel, I haven't finished my table, need to add another drawer and complete the dust collection portion to hook up to my system (another round tuit). I often have my saw set up to cut rails / stiles and it is quite convenient to be able to make a new one if I (ever) screw one up (hah). Hate to admit it, but last week I was assembling the interior lining for my DIL blanket chest. I made a frame and panel liner that drops into the White oak chest, installing a cover rail on the top edge of the oak to capture the liner. Well I started to assemble the front panel section and suddenly realized I had a cope cut upside down on one stile. Made me feel a little (lot) dumb as I stood there trying to figure out how I did that. Glad I didn't have to change my setups. I have a fairly large dedicated shop (30' X 30') so the space isn't a real concern. However I don't know that I would save a lot anyway as I would have to provide a storage area for all the equipment I have stored in the router table - and I also use the table as an assembly area occasionally.