General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
by Phil Joines KRum, Tx 12/9/07, 5:39 AM
1 Reply · 28 ViewsLast post 12/9/07, 5:14 PM by Brian in Brighton -
I need advice about external computer backup 2
by Lee Grindinger 12/6/07, 12:43 PM
25 Replies · 119 ViewsLast post 12/9/07, 4:54 PM by Bill Howatt -
by Dean Lapinel 12/8/07, 4:52 PM
20 Replies · 61 ViewsLast post 12/9/07, 4:42 PM by David Yoho -
WC Benefit Christmas Auction, Last Day *LINK*
by Jim Shaver - Oakville, Ontario 12/9/07, 3:53 PM
0 Replies · 23 ViewsLast post 12/9/07, 3:53 PM by Jim Shaver - Oakville, Ontario -
by Ellis Walentine 12/9/07, 2:44 PM
0 Replies · 25 ViewsLast post 12/9/07, 2:44 PM by Ellis Walentine -
by Ron Hildreth 12/7/07, 5:14 PM
19 Replies · 92 ViewsLast post 12/9/07, 4:38 AM by Geary from NJ -
by Ben 12/8/07, 11:33 PM
1 Reply · 24 ViewsLast post 12/9/07, 3:18 AM by Jack -
by HC Sakman 12/8/07, 7:06 PM
0 Replies · 22 ViewsLast post 12/8/07, 7:06 PM by HC Sakman -
by Ken Krawford 12/8/07, 3:04 PM
1 Reply · 30 ViewsLast post 12/8/07, 4:11 PM by Binen -
Cleaning Sandpaper for Performax??
by Barry Irby 12/8/07, 2:01 PM
2 Replies · 30 ViewsLast post 12/8/07, 3:13 PM by Barry Irby -
OTradio controlled helicopters
by Tom Norton 12/4/07, 10:48 PM
10 Replies · 42 ViewsLast post 12/8/07, 3:13 PM by Mark Goodall - ATL - tooljunkie -
by Dustmaker Mike 12/8/07, 12:58 PM
2 Replies · 24 ViewsLast post 12/8/07, 2:06 PM by Ron Hildreth -
by Mark Mandell 12/8/07, 4:10 AM
2 Replies · 31 ViewsLast post 12/8/07, 1:09 PM by Barry Irby -
by Winnemucca Lynn 12/6/07, 10:16 PM
8 Replies · 43 ViewsLast post 12/8/07, 4:46 AM by Winnemucca Lynn -
by Ron Hildreth 12/7/07, 12:35 PM
25 Replies · 95 ViewsLast post 12/8/07, 4:46 AM by Joe Pack -
by MoHusker 12/6/07, 9:33 PM
10 Replies · 45 ViewsLast post 12/8/07, 4:21 AM by ScottS -
by thomas in ak 12/7/07, 5:28 PM
2 Replies · 24 ViewsLast post 12/8/07, 3:10 AM by Steve in Fresno Goooo Dogs -
Removing Crayon Off a Wood Floor
by Scott in Eastern Iowa 12/6/07, 1:58 AM
10 Replies · 34 ViewsLast post 12/8/07, 12:50 AM by Art Silva -
by Mark Valsi 12/6/07, 3:26 PM
7 Replies · 36 ViewsLast post 12/8/07, 12:35 AM by Nick Tuzzolino -
by Jason Roehl in Lafayette, IN 12/7/07, 1:50 PM
4 Replies · 32 ViewsLast post 12/8/07, 12:16 AM by Jason Roehl in Lafayette, IN -
Woodworking is a wonderful hobby... Until
by Gary Camp Bend, Oregon 12/6/07, 8:59 PM
7 Replies · 36 ViewsLast post 12/8/07, 12:07 AM by Carol - now in NC Nebraska -
OT - Rube Goldberg lives! *LINK*
by Tom Pilsbury 12/7/07, 4:58 AM
4 Replies · 29 ViewsLast post 12/7/07, 9:08 PM by JohnKJordan in East TN -
by Lee Schierer - McKean, PA 9/28/07, 12:16 AM
18 Replies · 39 ViewsLast post 12/7/07, 3:41 PM by Mark Valsi -
by Wayne 12/7/07, 2:13 AM
1 Reply · 28 ViewsLast post 12/7/07, 6:55 AM by Brian in dawson creek -
Dedicated mortiser or router table?
by Dan Mitchell 12/5/07, 6:40 AM
22 Replies · 74 ViewsLast post 12/7/07, 4:44 AM by Art Silva -
warped wood------WebKitFormBoundaryvG+Z4Lo7QpgTMJ+
by Bob Ho------WebKitFormBoundaryvG+Z4Lo7QpgTMJ+K 12/7/07, 3:05 AM
1 Reply · 23 ViewsLast post 12/7/07, 3:19 AM by JohnKJordan in East TN -
using stock feeder to make raised panels on 3 HP s
by Todd 12/6/07, 2:47 AM
6 Replies · 50 ViewsLast post 12/7/07, 2:47 AM by Ellis Walentine -
OT Rats in crawl space/insulation follow up
by Dan Mitchell 12/5/07, 6:35 AM
9 Replies · 38 ViewsLast post 12/7/07, 2:45 AM by Dan Mitchell -
Only 3 Days Left � Auction Pen *LINK*
by Jim Shaver - Oakville, Ontario 12/7/07, 1:01 AM
0 Replies · 27 ViewsLast post 12/7/07, 1:01 AM by Jim Shaver - Oakville, Ontario -
Semi-OT - hardboard as counter top?
by John E 12/6/07, 4:17 PM
4 Replies · 39 ViewsLast post 12/6/07, 9:44 PM by George (Oxford, NC)



