Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

using stock feeder to make raised panels on 3 HP s

Posts

using stock feeder to make raised panels on 3 HP s

#1

using stock feeder to make raised panels on 3 HP s

Todd

>I'm in the process of making 14 interior ash doors. Each door has 2 panels measuring 24x24 (square) and 24x36 (with an arch). I plan to buy a stock feeder as it is much safer but was wondering if anyone had advise on how to use the stock feeder to make the arched panels. Does anyone know of a book or other articles that could shed some light on this subjevt?

Re: using stock feeder to make raised panels on 3 HP s

#2

Ellis Walentine

Question for you

Ellis Walentine

>I'm not exactly sure what isn't clear about using your stock feeder for this operation. You are using a shaper with a big panel-raising cutter, correct? The stock feeder will work in conventional mode for all the straightaways (shape the cross-grain passes first). For the arch tops, depending on the shape and nature of the arch detail, you will have to use a starting pin and hand-feed your panels, then possibly clean up any inside details with chisels, depending on the design.

Ellis Walentine, Host

Re: using stock feeder to make raised panels on 3 HP s

#3

Lee Grindinger

Like the E-Man says

Lee Grindinger

>A power feeder won't be of much help for arched panels. One thing I used to do to make hand feeding these panels safer was to make an auxiliary plywood table, flip the cutter so it was cutting from the underside and reverse the direction on the shaper.

The scary part about these large cutter heads is what happens when the board tips up into them. This whole scenario is impossible if the the cut is taking place from the underside. The only issue with doing this is that narrow panels lose some of the face that's riding on the table as the profile is cut.

Lee

Re: using stock feeder to make raised panels on 3 HP s

#4

Re: Stock Feeder

Mark Mandell - Gone Round In Jersey

>Todd,

The only feeders I've ever seen were straight-line tools only; primarily for production runs far in access of your 14 door panels.

With crowned panels, you're going to be hand feeding those cuts anyway. To increase the safety factor and get a better cut, do these in several passes with the final cut thin so that you can minimize any tearout and still eliminate burning of the cut surface.

mm

Re: using stock feeder to make raised panels on 3 HP s

#5

I agree...

Kris Lasure

>I just finished building 12 interior doors myself using poplar for rails and stiles and 1 1/8" MDF for the panels as these doors will be painted. I have a 5hp shaper with 1 hp feeder and ran all the rails and stiles and long sides of panels with the feeder. However, when it came to coping the rails and running the ends of the panels, I ran those by hand due to the narrow dimension of each.

With my poplar rails and stiles, I was getting some chipout along the stick profile. I added a 3/4" MDF sub fence and ran the MDF into the cutter to make a zero clearance fence and my chipout was eliminated. May be something to think about.

kl

Re: using stock feeder to make raised panels on 3 HP s

#6

Re: Question for you

Todd

>I did not know if there was a way to make a jig that would allow the use of the power feeder. i.e. the panel is concave, therefore could I create a convex curve that matches 1/2 the panel, use the power feeder to feed along this curved path? After reading the post today, it does not look like this is possible.

Re: using stock feeder to make raised panels on 3 HP s

#7

Ellis Walentine

Conditional response

Ellis Walentine

>You can only do this if the concave curve is a segment of a circle. Any irregular curve won't feed properly. I used to use a big pin router to do stuff like this, where I could make a template under the workpiece to follow the pin and have the cutterhead above the work. It is a pretty scary proposition, regardless.

I think that if your panels are curved, you will end up feeding by hand. It is a time-honored but tricky job. Be very careful.

Ellis Walentine, Host