Hand Tools
Traditional tools, sharpening, restoration, usage techniques.
Related: Hand Tools archive
Topic list
-
TopicStatisticsLast post
-
by John Weber - GO BUCKS! 3/8/04, 10:42 PM
21 Replies · 184 ViewsLast post 3/10/04, 11:41 AM by Jack from Maine -
Tip for flattening waterstones
by Derek Cohen (in Perth, Australia) 3/8/04, 2:50 PM
8 Replies · 134 ViewsLast post 3/10/04, 5:34 AM by kevin toomey -
Bevel Angle for Japanese Chisels
by Mark Schroeder (Norfolk, VA) 3/9/04, 11:57 PM
3 Replies · 103 ViewsLast post 3/10/04, 3:29 AM by Wiley Horne--Glendora CA -
by Luke Herzberg 3/9/04, 5:23 PM
4 Replies · 81 ViewsLast post 3/10/04, 12:19 AM by Alan Hamilton -
by George D. Huron 3/9/04, 7:49 PM
7 Replies · 118 ViewsLast post 3/9/04, 11:02 PM by George D. Huron -
Buying used hand tool in Canada
by William 3/8/04, 10:16 PM
7 Replies · 121 ViewsLast post 3/9/04, 9:49 PM by William -
by TheHeretic 3/8/04, 12:20 AM
8 Replies · 87 ViewsLast post 3/9/04, 8:16 PM by Francisco Luna -
by Bill Houghton 3/7/04, 5:06 PM
8 Replies · 112 ViewsLast post 3/9/04, 7:53 PM by Scott Burr in Ben Lomond CA -
by Richard March 3/6/04, 1:43 AM
7 Replies · 210 ViewsLast post 3/9/04, 7:01 PM by Jim Yehle in Salt Lake -
by Dan Clermont in Burnaby 3/9/04, 3:08 PM
1 Reply · 78 ViewsLast post 3/9/04, 5:57 PM by Don Thompson, Cutler Ridge, South of Miami FL -
by Barry Va Beach 3/9/04, 2:07 AM
2 Replies · 84 ViewsLast post 3/9/04, 5:01 PM by Barry - Va Beach -
source for a GOOD mini tape measure?
by marketymarkmark 2/26/04, 1:48 AM
10 Replies · 147 ViewsLast post 3/9/04, 4:27 PM by Christopher Fitch -
by bidough 3/8/04, 10:57 PM
4 Replies · 72 ViewsLast post 3/9/04, 4:15 PM by Ernie Miller -
by Matt -- Los Angeles 3/6/04, 7:13 PM
15 Replies · 87 ViewsLast post 3/9/04, 3:46 PM by Matt -- Los Angeles -
by Doug 3/9/04, 3:54 AM
2 Replies · 83 ViewsLast post 3/9/04, 7:02 AM by wally b -
by Angelo in Cornwall, NY 3/8/04, 1:52 AM
4 Replies · 84 ViewsLast post 3/9/04, 1:52 AM by Angelo in Cornwall, NY -
by Moses Yoder in White Pigeon, MI 2/27/04, 10:20 AM
6 Replies · 82 ViewsLast post 3/9/04, 1:17 AM by Todd O. Cronkhite Native of Maine -
by Todd O. Cronkhite Native of Maine 3/7/04, 11:55 PM
5 Replies · 114 ViewsLast post 3/9/04, 12:55 AM by Todd O. Cronkhite Native of Maine -
by walt quadrato 3/8/04, 8:44 PM
4 Replies · 71 ViewsLast post 3/9/04, 12:48 AM by Angelo in Cornwall, NY -
by Steve Roxberg 3/8/04, 8:17 PM
1 Reply · 135 ViewsLast post 3/8/04, 11:32 PM by Rusty Miller -
by Dan Clermont inBurnaby 3/8/04, 5:31 AM
4 Replies · 67 ViewsLast post 3/8/04, 7:25 PM by Barry Va Beach -
by Terry in Denver 3/8/04, 7:10 PM
0 Replies · 183 ViewsLast post 3/8/04, 7:10 PM by Terry in Denver -
by Bob Smalser, Seabeck, WA 3/5/04, 5:40 PM
8 Replies · 156 ViewsLast post 3/8/04, 6:04 PM by Dave Anderson Chester, NH -
by Thomas Williams - Columbus Ohio 3/2/04, 11:49 PM
22 Replies · 109 ViewsLast post 3/8/04, 5:28 PM by Joe Rogers,Northern Virginia -
by Rolf Schmid 3/8/04, 2:50 PM
1 Reply · 81 ViewsLast post 3/8/04, 4:13 PM by Cameron -
by Ernie Miller 3/5/04, 3:28 PM
11 Replies · 89 ViewsLast post 3/8/04, 3:40 PM by deanj -
Opinions on chisel comparison purchase
by Wendell @ Murphy, TX 3/7/04, 4:40 AM
3 Replies · 75 ViewsLast post 3/8/04, 3:22 PM by Ted Shuck -
by Richard Gillespie 3/6/04, 12:37 PM
11 Replies · 169 ViewsLast post 3/8/04, 2:52 PM by Charles -
by David Yoho 3/8/04, 12:48 PM
0 Replies · 98 ViewsLast post 3/8/04, 12:48 PM by David Yoho -
Question on Stanley WWII-era bench planes
by Eric from Little Rhody 3/7/04, 2:14 PM
2 Replies · 167 ViewsLast post 3/8/04, 12:33 PM by Eric from Little Rhody



