General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
by Chuck Lenz 11/22/10, 7:40 PM
0 Replies · 18 ViewsLast post 11/22/10, 7:40 PM by Chuck Lenz -
trash can cyclone lid ??? *LINK*
by del schisler 11/20/10, 8:51 PM
7 Replies · 48 ViewsLast post 11/22/10, 5:50 AM by Walt Smith -
Semi OT -Bluetooth Headphones *LINK*
by Andy Lincoln 11/21/10, 5:47 PM
1 Reply · 23 ViewsLast post 11/22/10, 12:24 AM by Scott Burr in Ben Lomond CA -
by Joseph Mulherin, Sr 11/20/10, 9:31 PM
5 Replies · 14 ViewsLast post 11/21/10, 10:57 PM by Joseph Mulherin, Sr -
If you have been really good, and Santa
by Keith Newton----Little Rock, Arkansas 11/20/10, 5:56 PM
4 Replies · 38 ViewsLast post 11/21/10, 9:30 PM by mike -
by Randy Johnson 11/21/10, 4:52 PM
3 Replies · 35 ViewsLast post 11/21/10, 7:17 PM by Howard Norman -
by Doug Reynolds in Seattle 11/21/10, 6:51 PM
1 Reply · 11 ViewsLast post 11/21/10, 6:56 PM by Bill Tindall, E.TN. -
by Ralph Lipeles 11/19/10, 10:57 PM
8 Replies · 27 ViewsLast post 11/21/10, 4:09 AM by Barry -
by DizD 11/20/10, 7:24 PM
3 Replies · 22 ViewsLast post 11/21/10, 2:17 AM by Bill Houghton -
Tool justification? Ridgid Spindle/Belt sander *LINK*
by JL 11/20/10, 2:17 AM
11 Replies · 127 ViewsLast post 11/21/10, 12:59 AM by Bob Entwisle -
End of season find. Would you pay $5
by Gary Smyth 11/20/10, 3:59 PM
7 Replies · 17 ViewsLast post 11/20/10, 10:51 PM by steve mackay -
by Bill Tindall, E.TN. 11/19/10, 1:10 PM
13 Replies · 42 ViewsLast post 11/20/10, 9:34 PM by Bill Tindall, E.TN. -
by Joe Pack 11/20/10, 4:45 PM
1 Reply · 26 ViewsLast post 11/20/10, 9:14 PM by Dale Lenz -
by George 11/19/10, 9:34 PM
7 Replies · 39 ViewsLast post 11/20/10, 7:28 PM by George -
Can't get wirless routers... yes plural to work!!
by Frank on Chestnut Hill 11/18/10, 5:12 PM
9 Replies · 23 ViewsLast post 11/20/10, 5:41 PM by Dave Paine -
by Ellis Walentine 11/19/10, 9:24 PM
9 Replies · 12 ViewsLast post 11/20/10, 4:53 PM by Jerry Nicholson -
Letting wood "equilibrate" after cutting...
by JL 11/19/10, 9:36 PM
8 Replies · 26 ViewsLast post 11/20/10, 1:35 PM by Clint Searl -
by Jim in Burlington Ont. 11/20/10, 12:50 PM
1 Reply · 27 ViewsLast post 11/20/10, 1:03 PM by charles in mtl. -
Probably OT: What kind of screws are these?
by Henry Higginbotham 11/19/10, 5:48 PM
9 Replies · 16 ViewsLast post 11/20/10, 3:23 AM by Henry Higginbotham -
OK, So Who sets the nails in interior trim?
by Barry Irby 11/18/10, 10:11 PM
16 Replies · 27 ViewsLast post 11/20/10, 2:45 AM by Bill Houghton -
by Alan Young 11/19/10, 1:52 PM
9 Replies · 15 ViewsLast post 11/20/10, 2:23 AM by Don Orr -
by Ralph Lipeles 11/19/10, 2:51 PM
2 Replies · 12 ViewsLast post 11/19/10, 11:04 PM by Ralph Lipeles -
by Jim in Burlington Ont. 11/19/10, 12:54 PM
2 Replies · 14 ViewsLast post 11/19/10, 10:32 PM by Ray - Middletown, IN -
Do you have a preferred primer???
by Barry Irby 11/18/10, 10:20 PM
8 Replies · 29 ViewsLast post 11/19/10, 9:51 PM by FredD -
by steve mackay 11/19/10, 3:39 PM
1 Reply · 14 ViewsLast post 11/19/10, 4:06 PM by Bill Tindall, E.TN. -
by Dale Lenz 11/18/10, 8:28 PM
8 Replies · 26 ViewsLast post 11/19/10, 2:30 PM by DaleLenz -
by Jennifer@Indy.USA 11/18/10, 4:38 PM
15 Replies · 72 ViewsLast post 11/19/10, 2:39 AM by Jennifer@Indy.USA -
Authoritive word on hide glue working time
by Bill Tindall, E.TN. 11/18/10, 1:29 AM
3 Replies · 38 ViewsLast post 11/19/10, 1:40 AM by Bill Tindall, E.TN. -
by Thomas Norton 11/18/10, 2:35 AM
7 Replies · 33 ViewsLast post 11/19/10, 1:23 AM by Bill Tindall, E.TN. -
by DaleLenz 11/18/10, 5:16 PM
7 Replies · 27 ViewsLast post 11/18/10, 8:48 PM by Jerry Nicholson



