Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Inlay Work Not Going So Well

Posts

Inlay Work Not Going So Well

#1

Inlay Work Not Going So Well

George Colonel's Workshop-Havertown PA

Good Afternoon Friends,

I bought a Jessada Inlay Kit about a dozen years ago and never used it until yesterday. I want to install a Dutchman/ patch, as invisable as possible, on a plank of QS sycamore which will be included in a cherry headboard/foot board for a 4-poster Shaker style bed. The sycamore plank has a defect, almost like bark inclusion/elongated knot running thru it. The defect is 4 3/4" long and varies between 1/2" to 1" in width on one of the sides, but is "live-with-able" on the other side of the board. I have a scrap piece of sycamore which closely matches the grain and color of the wood surrounding the patch area.

I decided to make a couple practise inlays in scrap poplar just to get the hang of it. The first attempt yielded a very tight fitting inlay. This morning I swapped out my router sub base for a clear base but ran into problems evacuating the poplar. The router bit broke off where the spiral transitions to the 1/4" shank. I was successful in routing the perimneter, but as soon as I began to move the router back and forth thru the patch area, the bit snapped.

I was less than aggressive throughout this exercise in poplar. Sycamore is a bit harder to work, and I am now challenging the wisdom of an inlay. I'd appreciate some input especially from wood workers who have inlay experience.

George

Re: Inlay Work Not Going So Well

#2

Re: Inlay Work Not Going So Well *LINK*

Bruce, a MN Galoot

I wish I could tell you the details, but I can't. A bunch of years ago, my former BIL showed me a bit combination he had for his router. Using a template, one bit cut the inlaid piece and the other bit cut the recess. It was specifically designed for plastics like Formica, but no reason it can't be used for other applications.

Or, you could use something like


this

Re: Inlay Work Not Going So Well

#3

Ellis Walentine

Another Dutchman technique

Ellis Walentine

You might want to try a more empirical approach. Besides matching the grain to the surrounding wood, you want to make the fit as tight as possible. The best way to do that is to taper your patch slightly and try to keep the edges parallel to the grain of the wood wherever possible.

For example, on this repair, I'd rout a straight slot, parallel to the grain if possible, where you want the plug, then carefully square out the ends with a chisel, angling your cut back at an angle. Then make the plug by cutting it roughly to shape with a bandsaw and then sizing it with either planes and chisels or a disk sander. Make the Dutchman slightly oversize and put a slight draft it so it wedges tightly into the slot when you clamp it home. Use a white or clear glue to minimize the visibility of the glue line.

Just a thought.

Ellis

Re: Inlay Work Not Going So Well

#4

Re: Inlay Work Not Going So Well

del schisler

Mite be a cheep bit?? I do inlay i use the whiteside set up. So far havent broke a bit. Not saying it won't happen. I would say the 1/4" bit may have a cheepo? My fit's are tight. What you can do is use a sanding block and with the inlay piece sand a slite taper down to the bottom or tapper the side's leve the top along. Dont come all the way to the top. So that it is not a sharp edge. good luck

Re: Inlay Work Not Going So Well

#5

Was it a downcut spiral?

Dick Coers

I hate those downcuts. I quickly set that aside, and replaced it with an upcut. Never had any chip out problems with an upcut, it gets the chips out very cleanly, and cuts faster. I've also used the 1/8 rig to cut the outline, but then put in some regular guide bushings with a 1/4 bit. I've used much bigger bits with standard bushings, but cleaning out the corners doesn't make for quick work. I love using these, and have always had good luck. Just don't try the fit, because it can be really tough bringing out the inlay to get the glue under it.

Re: Inlay Work Not Going So Well

#6

Re: Inlay Work Not Going So Well

FredD

Del, are you related to Norm Crosby, just curious ? ;-))

FredD

Re: Inlay Work Not Going So Well

#7

Re: Inlay Work Not Going So Well

David Yoho

George, I feel for you, buddy. Many times when I've used my inlay bit setup I've worried about that tiny spiral breaking off. However, I've used mine in much harder woods than poplar or sycamore and it's done well so far. Mine is made by Whitside.

One thing you might try, since it sounds like your patch/inlay is not too small, is to use the inlay bit around the perimeter of your mortised cut and then switch to a straight or spiral but to "hog" out the rest of the waste. This would save the small inlay bit from doing all the grunt work.

If you need to get another setup, give the Whiteside a try. I think Woodcraft carries them probably.

Re: Inlay Work Not Going So Well

#8

Thanks-Ordered Replacement Kit

George Colonel's Workshop-Havertown PA

Thank you All,

I appreciate the thoughts. I can't imagine why I hadn't thought to use the 1/8" for the sole purpose of mortising the perimeter/cutting the patch. I have multiple bushings and will set up a 2nd router and 1/4" bit for evacuation. That makes a lot of sense. And Dick, to answer your question: yes I think it was a downcut spiral. Too late to look as its thrown away now.

George