If you sell to woodworkers, your customers are already here

General Woodworking

Cross-cutting topics, techniques, and questions that don’t fit a specialty.

ACTIONS | Post new topic

Topic list

Topic

Statistics

Last post
Acclimatizing lumber in/or out of the shop?

by Bri in Mtl 1/22/07, 12:56 PM

1 Reply · 62 Views

Last post 1/22/07, 5:14 PM by Dale Lenz
Coolness Test

by Ray Binnicker 1/21/07, 3:35 PM

7 Replies · 99 Views

Last post 1/22/07, 4:54 PM by Tom Sontag
finishes

by Floyd E. Harmon 1/19/07, 12:55 PM

4 Replies · 78 Views

Last post 1/22/07, 3:43 PM by Paul Dwight
I completed a Project! (Long)

by Joe 1/20/07, 3:49 PM

15 Replies · 88 Views

Last post 1/22/07, 1:21 PM by Mark Goodall - ATL - tooljunkie
MDF Dust Question

by J. Robison 1/20/07, 7:43 PM

4 Replies · 80 Views

Last post 1/22/07, 4:57 AM by Michael Dresdner
restaining

by Darrell West 1/21/07, 11:30 PM

2 Replies · 198 Views

Last post 1/22/07, 4:49 AM by Michael Dresdner
Furniture Makers

by Paul A 1/20/07, 8:44 PM

7 Replies · 78 Views

Last post 1/22/07, 2:51 AM by Don Henthorn
Storage door construction ideas?

by Alan Tolchinsky 1/21/07, 4:10 PM

4 Replies · 127 Views

Last post 1/22/07, 2:19 AM by Alan Tolchinsky
Fix this warp help.

by Bri in Mtl 1/20/07, 12:15 PM

5 Replies · 64 Views

Last post 1/22/07, 1:43 AM by DeanG
"Right side" of veneer

by Barry Daniel 1/18/07, 2:24 AM

7 Replies · 153 Views

Last post 1/22/07, 1:02 AM by Barry Daniel
Finishing a wooden counter top

by lee beeden 1/21/07, 10:26 PM

5 Replies · 97 Views

Last post 1/21/07, 11:55 PM by Steve Schoene
DISPLAY TABLE PLANS

by CARL BARTON 1/21/07, 2:11 PM

1 Reply · 106 Views

Last post 1/21/07, 11:44 PM by Earl
Table with butterfly

by Don Henthorn 1/20/07, 4:45 PM

6 Replies · 125 Views

Last post 1/21/07, 7:56 PM by Larry Clinton in Frankfort, Indiana
To Burn ...or ....Not to Burn

by Scott in Eastern Iowa 1/21/07, 6:18 AM

5 Replies · 60 Views

Last post 1/21/07, 7:01 PM by wilbur
OT Compressor problem

by Earl 1/20/07, 2:56 AM

2 Replies · 67 Views

Last post 1/21/07, 5:08 PM by Barry Irby
OT: Windows XP Network ?

by Robert Hutchins 1/20/07, 4:21 AM

3 Replies · 63 Views

Last post 1/21/07, 3:56 PM by Bill Howatt
glider bearings

by Orion/.Denton, TX 1/21/07, 3:44 PM

0 Replies · 56 Views

Last post 1/21/07, 3:44 PM by Orion/.Denton, TX
Fireplace moisture meter

by Stephen Kirk in Quakertown, PA 1/21/07, 3:17 PM

0 Replies · 57 Views

Last post 1/21/07, 3:17 PM by Stephen Kirk in Quakertown, PA
shop heater

by DeepWoods in MN 1/19/07, 8:19 PM

3 Replies · 54 Views

Last post 1/21/07, 4:42 AM by DeepWoods in MN
WoodSucker Dust Collection

by Roger 1/20/07, 7:47 PM

1 Reply · 61 Views

Last post 1/21/07, 12:31 AM by mdclor
19" LCD Monitor Update

by Robert Hutchins 1/18/07, 6:43 PM

18 Replies · 102 Views

Last post 1/20/07, 10:57 PM by Robert Hutchins
Magnetic switch modification OK?

by Bri in Mtl 1/18/07, 4:43 PM

9 Replies · 75 Views

Last post 1/20/07, 9:17 PM by Kent in Emmaus, PA
Slllllooooooowwwwwww

by Don Henthorn 1/19/07, 2:10 AM

10 Replies · 67 Views

Last post 1/20/07, 6:22 PM by Dave Bair
Slurry splash

by Franz Stuppe 1/14/07, 2:15 AM

4 Replies · 79 Views

Last post 1/20/07, 5:10 PM by Franz Stuppe
Reply to Tandy in Connersville.

by Don Henthorn 1/20/07, 5:05 PM

1 Reply · 45 Views

Last post 1/20/07, 5:06 PM by Don Henthorn
Mag Jig Magnets

by Pat Schupbach 1/20/07, 3:15 PM

1 Reply · 71 Views

Last post 1/20/07, 4:42 PM by Andy Lincoln
OT: Whirlpool Duet 9300 Vibration in Spin Cycle

by Paul Leuba 1/18/07, 5:46 PM

10 Replies · 120 Views

Last post 1/20/07, 4:13 PM by Paul Leuba
Need accurate miters - tips & tricks?

by Joe 1/15/07, 2:24 PM

8 Replies · 87 Views

Last post 1/20/07, 2:43 PM by Bart Goldberg
Makita chop saw problem solved!

by Tom Norton 1/20/07, 2:38 PM

0 Replies · 79 Views

Last post 1/20/07, 2:38 PM by Tom Norton
Gluing Soft Maple

by Rob Scrimgeour 1/20/07, 11:36 AM

2 Replies · 82 Views

Last post 1/20/07, 2:33 PM by bill tindal, E.TN

ACTIONS | Post new topic