General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
OT You knew there was at least one Blonde Easter
by Dustmaker Mike 3/24/08, 10:52 AM
0 Replies · 59 ViewsLast post 3/24/08, 10:52 AM by Dustmaker Mike -
by Bart Goldberg 3/23/08, 7:31 PM
7 Replies · 44 ViewsLast post 3/24/08, 4:28 AM by henthorn -
by North of the Border 3/22/08, 9:29 PM
6 Replies · 19 ViewsLast post 3/24/08, 4:24 AM by Rod Peterson -- Ormond Beach -
by Mike Jones, Redding, CA 3/23/08, 10:45 PM
2 Replies · 28 ViewsLast post 3/24/08, 3:42 AM by Bob Entwisle -
The mini demilune table is Done!
by Bob Entwisle in NJ 3/22/08, 9:49 PM
13 Replies · 47 ViewsLast post 3/24/08, 2:26 AM by Charles Jackson III -
Looking for a new bench grinder
by Brian D 3/23/08, 5:30 PM
2 Replies · 28 ViewsLast post 3/24/08, 2:23 AM by Bill Tindall, E.TN -
OT: Nafco Permastone flooring?
by Bill Howatt 3/23/08, 4:44 PM
2 Replies · 23 ViewsLast post 3/24/08, 1:53 AM by George Koch -
right angle/close quarters drill....
by Ray Newman 3/21/08, 3:37 AM
15 Replies · 51 ViewsLast post 3/24/08, 1:16 AM by Dale Lenz -
by jared 3/23/08, 12:04 PM
8 Replies · 25 ViewsLast post 3/24/08, 12:39 AM by jared -
FW -Square peg in a round hole tip works great!
by North of the Border 3/23/08, 4:08 PM
3 Replies · 25 ViewsLast post 3/24/08, 12:19 AM by North of the Border -
by Bill Hammond, Oregon Coast 3/22/08, 11:05 PM
4 Replies · 25 ViewsLast post 3/23/08, 10:31 PM by Howard In Toronto -
by Dan Manturi 3/21/08, 12:52 PM
10 Replies · 58 ViewsLast post 3/23/08, 7:23 PM by Jack in Brooklyn -
problems with a tung oil finish
by Glenn 3/20/08, 1:51 PM
6 Replies · 181 ViewsLast post 3/23/08, 7:20 PM by Michael Dresdner -
by Chuck W 3/23/08, 12:46 PM
1 Reply · 44 ViewsLast post 3/23/08, 7:09 PM by Carol - now in NC Nebraska -
PBS wood shows - does anyone has duplicate DVDs ?
by North of the Border 3/23/08, 3:59 PM
1 Reply · 24 ViewsLast post 3/23/08, 4:01 PM by North of the Border -
by Joe 3/23/08, 3:37 AM
2 Replies · 18 ViewsLast post 3/23/08, 1:46 PM by North of the Border -
by Dustmaker Mike 3/23/08, 12:09 PM
1 Reply · 15 ViewsLast post 3/23/08, 12:39 PM by Joseph Mulherin, Sr. -
by Bill Pfahl in Virginia 3/22/08, 8:29 PM
6 Replies · 24 ViewsLast post 3/23/08, 11:50 AM by marc rosen -
by chris Parker 3/21/08, 6:51 PM
3 Replies · 21 ViewsLast post 3/23/08, 8:12 AM by Ralph Turney -
by Alan 3/23/08, 4:03 AM
0 Replies · 20 ViewsLast post 3/23/08, 4:03 AM by Alan -
Any good working in Central Illinois?
by Stephen Kirk in Quakertown, PA 3/22/08, 5:38 PM
3 Replies · 25 ViewsLast post 3/23/08, 12:53 AM by Dick Coers -
Happy birthday, Denis Ch�nard.
by Al Stokka 3/22/08, 12:47 PM
4 Replies · 77 ViewsLast post 3/23/08, 12:40 AM by Denis Ch�nard, Orl�ans, Ont. -
How to glue a wood splitter to phenolic insert?
by lise 3/22/08, 6:03 PM
3 Replies · 19 ViewsLast post 3/22/08, 10:50 PM by Steve in Denver -
by Ernie Miller 3/19/08, 1:59 PM
19 Replies · 61 ViewsLast post 3/22/08, 10:10 PM by Malcolm Timbers -
Cutting thin strips on table or band saw
by Gary Smyth 3/21/08, 7:13 PM
17 Replies · 28 ViewsLast post 3/22/08, 9:42 PM by Barry Irby -
by woodenleg 3/22/08, 6:05 PM
2 Replies · 21 ViewsLast post 3/22/08, 9:18 PM by Barry Irby -
by Ned Bulken 3/22/08, 5:58 PM
5 Replies · 32 ViewsLast post 3/22/08, 8:45 PM by Ned Bulken -
Request for help on source of lumber
by North of the Border 3/22/08, 3:32 AM
6 Replies · 86 ViewsLast post 3/22/08, 5:36 PM by North of the Border -
Should'a, would'a, could'a . . .
by steve mackay 3/22/08, 3:33 PM
2 Replies · 64 ViewsLast post 3/22/08, 4:50 PM by Gary Smyth -
What is the perfect pad sander?
by Bill Hammond, Oregon Coast 3/21/08, 8:07 PM
9 Replies · 47 ViewsLast post 3/22/08, 4:38 PM by Dave Bair - Eaton Rapids



