Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

How to re-flatten a panel

Posts

How to re-flatten a panel

#1

Bart Goldberg

How to re-flatten a panel

Bart Goldberg

>I'm in the process of making a desk for a friend's birthday. I made the top first - 56 inches wide x 38 inches deep all from flat sawn white oak. After sanding the top smooth, I had put it aside while I started on the carcass construction.

Now that I've completed the carcass - I went to check on the top and found that it has cupped from the center and is slightly "c" shaped.

I tried just laying on the floor with some scrap ply piled on top to re-flatten it- but it hasn't moved much after about a week. So, I'm thinking that I would try some clamping type method - I created some three sided boxes/clamping cauls - that I would use to clamp the panel too, and start using clamps to try and flatten it -

Any opinions?

Bart

Re: How to re-flatten a panel

#2

Re: How to re-flatten a panel

Clint Searl, at the base of Haycock Mtn

>I think it has a mind of its own and you're not gonna change it. I would rip it into four or five pieces and rejoin, alternating the crown, and finishing equally top and bottom. Good luck

Clint

Re: How to re-flatten a panel

#3

Re: How to re-flatten a panel

Barry Irby

>You have not said how badly cupped it is. If it's less than a half inch over the width, it is different that if it is substantially more.

IF it is slightly cupped you may be able to flatten it by putting it in place on the carcase and pulling into submission with whatever you are using to hold the top on.

You can flatten it by laying on the ground with the cupped side down and the convex side (hump) up. The theory is that the dampness of the earth will cause the short side to expand and the sun will cause the longer side to shrink. On a warm sunny day this may happened in an hour or two. At the point the panel is flat, apply finish to both sides as quickly as you can and fasten it into place.

And, Clint's method will work and may be better in the long run.

Re: How to re-flatten a panel

#4

Re: How to re-flatten a panel

Scott in Montana

>Bart,

You don't say where you live, but out of desperation I've had luck with this. Set the panel, crown up, on a flat surface out in the sun (presuming it's warm out). I've also placed weight on it at the same time, but nothing with too large of shadow. Check it every half hour or so and move your weight around. I'm thinking the sun or heat dries the crowned side and causes it to contract or shrink. I've also done this with cabinet doors.

Good luck,

Scott

Re: How to re-flatten a panel

#5

Re: How to re-flatten a panel

Ed Mulligan, Cape Cod

>Bart -

I'd install the top. Does it look OK? If no, let's look into workarounds.

Ed

Re: How to re-flatten a panel

#6

Re: How to re-flatten a panel

dave grinnell

>Hello,

If it's a decent size cup, i would not try to force it with clamps or screwing it to the base. Personally, that approach has ended tragically in that board breaking sound. Try moisture on the concave side and heat on the convex. Outside works good if you've got some nice morning dew and sunshine, if not, what's worked well for me is brushing on water to the concave and something like a halogen lamp on the convex, and a little patience. I've not used weights. Just be sure to sand it up again (because of the water) before finishing. Doing this I've corrected an 18 inch wide table top that had cupped well over an inch from crown to edge that had been a return to a previous boss. After doing this procedure, for good measure I cross braced it under the top, cause it's a crazy tree (you should see the leaves on the table, from the same tree, hysterical)But after several seasons, the top is fine.

Also, as more of a preventative note, i'll not build any "Free floating" parts (ie tops, lids and the like) until the end of a project. And if an unfinished panel or any other part is to sit around over night, i'll stack and sticker them with a little weight on top.

hope this helps

dave

Re: How to re-flatten a panel

#7

not necessary

Bill Tindall, E.TN

>A common occurrence that isn't a problem. The top will be held onto the desk, right? Be amazed how little force will be needed to pull it flat against the desk frame with table top fasteners or what ever you intend to use.

In an extreme case I once pulled more than 1" of bow out of a top by pulling it against a table frame.

Re: How to re-flatten a panel

#8

How was it stored while you were working on

henthorn

>the other parts. If you had it laying flat somewhere you probably have a moisture differential that will straighten itself out if you will just place it on edge where the air can get to both sides. Bill is right. I would just fasten it to the piece and it will probably be fine.