Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

right angle/close quarters drill....

Posts

right angle/close quarters drill....

#1

right angle/close quarters drill....

Ray Newman

>Little Voice tells me that I really need a good right angle/close quarters drill.

Today, I looked @ the 3/8" Milwaukee (USA made model) & the 3/8" Maikta corded units. The Milwaukee seemed to balance better than the Makita. Hefted a DeWalt 14 V cordless & it didn't feel right. Don't know if the DeWalt 12 V would balance/feel any better. The 12 v makes more sense as I already have a deWalt 12 V driver/3/8" drill.

Any recommendations?....

Re: right angle/close quarters drill....

#2

Avoid the DeWalt...

Clint Searl, at the base of Haycock Mtn

>I have one; it's large, heavy, cumbersome, and requires two hands. Sorry I bought it.

Clint

Re: right angle/close quarters drill....

#3

Milwaukee and Sioux

Mark Goodall - ATL - tooljunkie

>I've always have my eye on either the Milwaukee or Sioux, as they both look, feel good and have good reviews.

I feel bad that I can't give you a recommendation based on hands on experience. Perhaps I need to go shopping this weekend and repost next week ;)

Happy Woodworking!

Re: right angle/close quarters drill....

#4

Re: right angle/close quarters drill....

Chuck in ND

>I have a Sioux that I use occassionally. I really like it. It's not cordless, so I don't know if this is much help to you.

Re: right angle/close quarters drill....

#5

Re: right angle/close quarters drill....

Barry Irby

>Post your question again on the Turning board. Turners use these drills for bowl sanding. The bearings wear out quicker than might be expected and are not of the highest quality. They can be replaced with better bearings, but the procedure is tedious to get the drills reassembled. OTOH, sanding bowls is harsh and dusty and may be excessively hard on the drills. In daily ordinary use they may last a very long time. Also, the Sioux and Milwaukee are identical. There is also a cheap Chinese knock off.

Re: right angle/close quarters drill....

#6

Alan Young

Go the extra 1/8 inch and get the

Alan Young

>Milwaukee with the 1/2 chuck. I have two of these. One at home and one at work. Hold on tight though----they'll twist your wrists into a pretzel before you can think of letting go of the trigger!

Alan

Re: right angle/close quarters drill....

#7

Re: right angle/close quarters drill....

Chad Pearson

>I have the Milwaukee. I have no complaints and would buy it again.

Re: right angle/close quarters drill....

#8

Re: right angle/close quarters drill....

John K Jordan

>Same here. I use mine mostly for sanding bowls on the lathe. Of those I tried, it was balanced the best and the grip and trigger placement fit my hand perfectly. I've had mine maybe 6-7 years. I do blow the dust out of it on occasion.

JKJ

Re: right angle/close quarters drill....

#9

Re: right angle/close quarters drill....

Howard Norman

>As someone has noted the Sioux and Milwaukee corded drills are identical as far as I can tell. I have two of the Milwaukees They are very well balanced and feel "right". I also have one of the large 1/2" Milwaukees. It has a lot of power and is the one that I turn to when I am going to be drilling large,over one inch, holes.

Howard

Re: right angle/close quarters drill....

#10

Re: Milwaukee and Sioux

John McGaw

>I can vouch for the Milwaukee. It is powerful and well-balanced and fits the hand very well. I just got done drilling 1000 5mm holes (about 1.5 drill-bit's-worth) in a set of bookshelves using the LV jig with my Milwaukee without a problem.

Re: right angle/close quarters drill....

#11

Re: Milwaukee and Sioux

Neal in San Jose

>I had the Siioux for many years when I was a contractor. Must have drilled a bazillion holes with it. I finally wore it out and I'd buy another except I'm just a hobbiest now and can't justify one. I also have a little Makita 7.2 cordless that does a pretty good job, expecially when I slip in the 9.6 battery!

Re: right angle/close quarters drill....

#12

Re: right angle/close quarters drill....

George@Colonel's Workshop-Havertown PA

>Good Norning Ray,

I have the corded Milwaukee 3/9" drill and have been thoroughly satisfied with it for over 8 years. I bought my #1 and #3 sons the Sioux knockoff. What Barry says may be true, because #3 son had to have bearings replaced in his. However, jher did admit abusing it on the job site. The local Milwaukee Service center would not repair the Sioux, which surprised me. I thought they were manufactured at the same facility. Factory service is availan44 for the Siousx, its just not convenient to us. They both are fine tools. I recommend the Milwaukee.

G.Beorge44

Re: right angle/close quarters drill....

#13

I have the Dewalt 14V and used the others

Lee Schierer - McKean, PA

>I have a Dewlat 14 V cordless right angle drill. It has worked well for the times I have needed it. It has plenty of torque. I have no complaints, it was part of ht eset I bought, but has come in handy when I have needed it.

We had a Dewalt corded right angle and a Milwaukee corded angle drill where I used to work. The on/off switch on the Dewalt was somewhat dangerous because you tended to turn the motor on when just gripping the drill in tight quarters. The Milwaukee says it is only 3-7/8" tall but the point where the cord exits the body makes it about an inch or so more than that and the head is angled to the grip so it can be hard to apply pressure straight into the drill bit or screw driver tip.

Lee

Re: right angle/close quarters drill....

#14

Re: right angle/close quarters drill....

Binen

>I have no idea about your needs but I need one only occasionally. I looked and looked but couldn�t find anything at a price that made it worth buying. Finally I saw a corded one at Harbor Freight on sale for I think $19.99. I�ve had it now 3 years and it worked fine every time I needed it. Perhaps I have used it a dozen times in the last 3 years and driven under 100 screws. No idea how long it would last under hard use but for me this one will last years.

Binen

Re: right angle/close quarters drill....

#15

Jesper, Denmark

Re: Milwaukee and Sioux

Jesper, Denmark

>Milwaukee and Sioux are identical tools, except for the color and the labels.

Take your pick.

Re: right angle/close quarters drill....

#16

Dale Lenz

Re: These drills are dangers when...

Dale Lenz

>locking the bits down with a key. I always hit the paddle trigger, unsafe habit, : ' >. I bet the newer versions have keyless chucks. Mines about a 93' circa.