General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
by Peter Martin 3/25/25, 10:58 PM
4 Replies · 498 ViewsLast post 3/26/25, 11:35 PM by Dave Bair -
by John in NM 3/25/25, 12:44 PM
0 Replies · 460 ViewsLast post 3/25/25, 12:44 PM by John in NM -
Are you a member of a woodworking guild, club, or organization?
by Peter Martin 3/14/25, 10:01 AM
6 Replies · 520 ViewsLast post 3/20/25, 1:51 AM by Peter Martin -
by Peter Martin 3/4/25, 3:57 PM
6 Replies · 697 ViewsLast post 3/9/25, 12:55 PM by Peter Martin -
by Peter Martin 3/1/25, 1:13 PM
4 Replies · 820 ViewsLast post 3/3/25, 7:18 PM by Ellis Walentine -
by Peter Martin 2/27/25, 9:19 PM
0 Replies · 385 ViewsLast post 2/27/25, 9:19 PM by Peter Martin -
Entry hall table for a niece: Part 10
by Derek Cohen (in Perth, Australia) 2/23/20, 4:23 PM
0 Replies · 415 ViewsLast post 2/27/25, 8:12 PM by Derek Cohen (in Perth, Australia) -
Entry hall table for a niece: Part 13
by Derek Cohen (in Perth, Australia) 3/7/20, 6:26 PM
0 Replies · 494 ViewsLast post 2/27/25, 8:07 PM by Derek Cohen (in Perth, Australia) -
by Bill P. 2/23/25, 11:37 PM
5 Replies · 571 ViewsLast post 2/26/25, 12:15 PM by Peter Martin -
Modern Marvels: The Razor Sharp World of Saws
by Peter Martin 2/17/25, 10:51 PM
0 Replies · 474 ViewsLast post 2/18/25, 12:12 AM by Peter Martin -
Thermally modified wood solution?
by Peter Martin 2/15/25, 11:45 AM
4 Replies · 442 ViewsLast post 2/16/25, 2:53 PM by Henry (Raleigh NC) -
by Mark Mandell 3/26/24, 5:51 PM
4 Replies · 882 ViewsLast post 2/8/25, 3:12 PM by Jim DeLaney, Austintown, Ohio -
by Mike L 2/6/25, 2:03 AM
4 Replies · 546 ViewsLast post 2/7/25, 5:15 PM by Mike L -
The difference between a modern day board and one pulled from old barn
by Peter Martin 1/31/25, 6:46 PM
3 Replies · 640 ViewsLast post 2/3/25, 12:56 AM by Dave Bair -
by Mike L 2/1/25, 1:48 AM
1 Reply · 409 ViewsLast post 2/1/25, 2:02 PM by admin -
Better than Pegboard or French Cleats?
by admin 1/17/25, 5:10 AM
11 Replies · 944 ViewsLast post 1/23/25, 3:09 PM by DW -
by Bill P. 12/31/24, 2:47 AM
5 Replies · 1,055 ViewsLast post 1/15/25, 12:35 AM by Bill P. -
by admin 12/23/24, 12:55 PM
8 Replies · 1,004 ViewsLast post 1/14/25, 9:49 PM by Dw -
by admin 1/11/25, 2:11 AM
2 Replies · 367 ViewsLast post 1/11/25, 9:09 PM by Lee Schierer -
by Hank Knight 1/10/25, 12:44 PM
4 Replies · 646 ViewsLast post 1/11/25, 12:32 PM by Jason Roehl in Lafayette, IN -
Solved question about Delta 17-950 drill press quill play
by Bruce Mack 1/9/25, 6:37 AM
2 Replies · 558 ViewsLast post 1/9/25, 11:45 PM by Bruce Mack -
by Luke 1/5/25, 7:54 PM
4 Replies · 773 ViewsLast post 1/7/25, 9:13 PM by Luke -
May more of us strive to do remotely as well as Jimmy Carter.
by Bruce McCrory 12/31/24, 12:01 AM
2 Replies · 488 ViewsLast post 1/1/25, 11:39 PM by Joe Fleming -
by admin 12/30/24, 8:03 PM
1 Reply · 365 ViewsLast post 12/30/24, 8:31 PM by Dale Stansbery -
by rlipeles 12/13/24, 5:14 PM
10 Replies · 961 ViewsLast post 12/30/24, 3:13 AM by Derek Cohen (in Perth, Australia) -
by Mike L 12/18/24, 2:47 AM
2 Replies · 428 ViewsLast post 12/18/24, 2:39 PM by Mike L -
by Mike L 11/23/24, 1:26 PM
5 Replies · 646 ViewsLast post 11/24/24, 12:08 AM by John in NM -
One almost done a lot more to go.
by Mike L 11/18/24, 10:11 PM
1 Reply · 507 ViewsLast post 11/19/24, 1:00 AM by Ron in Sterling, CT -
by Maurice 11/5/24, 9:04 PM
4 Replies · 671 ViewsLast post 11/16/24, 6:17 PM by Bruce McCrory -
Solved Renovating a table
by Derek Cohen (in Perth, Australia) 9/17/24, 4:06 PM
11 Replies · 1,366 ViewsLast post 11/12/24, 3:48 AM by Maurice
