General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
Sanding sealer, end grain and lacquer
by Michael Foster 1/14/19, 12:48 AM
4 Replies · 26 ViewsLast post 1/14/19, 3:43 PM by Michael Foster -
by Joe 1/12/19, 8:17 PM
14 Replies · 30 ViewsLast post 1/14/19, 3:09 PM by Joe -
Drill press Counter weight question
by Barry Irby 1/12/19, 3:10 PM
16 Replies · 34 ViewsLast post 1/14/19, 12:41 PM by John in NM -
Hand cut half blind dovetails first attempt.
by Virgil Johnson 1/13/19, 5:22 PM
1 Reply · 23 ViewsLast post 1/14/19, 1:36 AM by Jack -
by Michael van pelt 1/13/19, 1:22 PM
0 Replies · 48 ViewsLast post 1/13/19, 1:22 PM by Michael van pelt -
Beech trees are dying, and nobody’s sure why
by Joe 1/12/19, 8:21 PM
2 Replies · 33 ViewsLast post 1/12/19, 11:37 PM by John McGaw -
Craftsman wood shaper: 113.239291
by Tom Lobenstein 1/12/19, 2:02 AM
1 Reply · 18 ViewsLast post 1/12/19, 1:21 PM by Jack Guzman from Maine -
Fluorescent vs LED- data from experiments
by Bill Tindall, E.TN. 1/10/19, 8:36 PM
10 Replies · 128 ViewsLast post 1/12/19, 1:15 PM by Barry Irby -
by Tom Lobenstein 1/12/19, 2:05 AM
0 Replies · 56 ViewsLast post 1/12/19, 2:05 AM by Tom Lobenstein -
A coffee table for my nephew - #8
by Derek Cohen (in Perth, Australia) 1/11/19, 5:14 PM
3 Replies · 39 ViewsLast post 1/12/19, 12:39 AM by Don Stephan -
by Larry 1/6/19, 1:00 AM
11 Replies · 44 ViewsLast post 1/11/19, 12:30 PM by Barry Irby -
The hand tool debate rages on......
by Bill Tindall, E.TN. 1/8/19, 10:22 PM
13 Replies · 39 ViewsLast post 1/10/19, 9:14 PM by Ellis Walentine -
Question for LED shop light users 2
by Bill Tindall, E.TN. 1/3/19, 2:49 PM
39 Replies · 114 ViewsLast post 1/10/19, 1:15 PM by John in NM -
by Ellis Walentine 1/9/19, 10:45 PM
1 Reply · 22 ViewsLast post 1/10/19, 12:08 AM by Bill Tindall, E.TN. -
by Lee 1/8/19, 7:47 PM
8 Replies · 39 ViewsLast post 1/9/19, 5:34 PM by vickytodds -
by Michael van pelt 1/5/19, 3:27 AM
5 Replies · 44 ViewsLast post 1/8/19, 9:09 PM by Larry -
by Jerry Nicholson 1/7/19, 8:42 PM
4 Replies · 50 ViewsLast post 1/8/19, 8:27 PM by Michael van pelt -
by John McGaw 1/7/19, 11:20 PM
1 Reply · 24 ViewsLast post 1/8/19, 6:34 PM by CJ in MPLS -
A coffee table for my nephew - #7
by Derek Cohen (in Perth, Australia) 1/7/19, 3:48 PM
8 Replies · 27 ViewsLast post 1/8/19, 4:53 PM by Derek Cohen (in Perth, Australia) -
Lifting drill press table questions
by Michael van pelt 1/4/19, 5:19 PM
21 Replies · 84 ViewsLast post 1/7/19, 10:54 PM by Keith Newton -
by Larry 12/17/18, 10:23 PM
20 Replies · 89 ViewsLast post 1/7/19, 6:44 PM by William Falberg -
by Brad Chenoweth 12/28/18, 5:23 PM
9 Replies · 103 ViewsLast post 1/7/19, 5:13 AM by Jason in Denver -
by Barry Irby 1/6/19, 7:26 PM
3 Replies · 29 ViewsLast post 1/7/19, 12:23 AM by Bob Lang -
by CJ in MPLS 1/5/19, 5:23 PM
2 Replies · 86 ViewsLast post 1/6/19, 11:17 PM by CJ in MPLS -
A coffee table for my nephew - #6
by Derek Cohen (in Perth, Australia) 1/5/19, 5:37 PM
2 Replies · 20 ViewsLast post 1/6/19, 3:48 PM by Derek Cohen (in Perth, Australia) -
by Thomas Skaggs 1/4/19, 5:51 PM
5 Replies · 42 ViewsLast post 1/5/19, 2:04 PM by ebd -
by Howie 1/4/19, 9:45 PM
1 Reply · 20 ViewsLast post 1/5/19, 2:30 AM by William Duffield -
by Michael van pelt 1/4/19, 4:25 PM
4 Replies · 37 ViewsLast post 1/4/19, 9:48 PM by Howie -
Dust collection for the bandsaw
by Derek Cohen (in Perth, Australia) 1/1/19, 4:44 PM
10 Replies · 40 ViewsLast post 1/4/19, 8:26 PM by John K Jordan -
Coffee Table for my nephew - #5
by Derek Cohen (in Perth, Australia) 1/2/19, 2:18 PM
19 Replies · 84 ViewsLast post 1/4/19, 6:53 PM by Ian Neuhaus