Lust at first sight... jointer
JL
18" Crescent jointer for sale. How would I ever get it into my basement though??
Knowledge You Can Build On — Est. 1998
Lust at first sight... jointer
JL
18" Crescent jointer for sale. How would I ever get it into my basement though??
Re: Lust at first sight... jointer
Chuck in Mtl.
if there is a will there is a way...
You could build a basement around it.
Re: Lust at first sight... jointer
John Lucas
I passed on a bandsaw I would kill for this summer. 20" metal cutting bandsaw with 3 phase motor that I could convert easily. It was very inexpensive. I didn't see any way that I could get it into my shop.
Re: Lust at first sight... jointer
Jesse Cloud
To paraphrase Jackie Gleason/Ralph Kramden "Humina, humina, humina". That is one sweet piece of iron.
Re: Lust at first sight... jointer
Joanne in Point Pleasant, PA
First, you get some strong friends who owe you favors or like you a lot. Then you take it apart and take it down in pieces. It may need cleaning anyway and that's easier in parts. Put down a carpet or blanket and slide it down the steps if you have to.Then you reassemble it. Be sure to put it in the spot where you REALLY want it, once it is down there. Much easier to move smaller parts. Looks beautiful and worth having.
Re: Lust at first sight... jointer
Jason Waters
Buy the jointer. Then build a shop to put it in. Problem solved!
Or cut a hole in the floor? Who cares if it's in the living room. Just watch out if it's joists..........Cover the hole with a cheap Wal-Mart rug...
It's a sweet looking one.
Re: Lust at first sight... jointer
Bill Houghton, Sebastopol, CA
Into is often easier than out of. Going down, you have gravity on your side.
In my youth, I got my motorcycle down the basement stairs solo; getting it out again, after the motor rebuild, required two people and a LOT more bad words. Not that I'd try either direction now.
All that…
Rod Peterson—Ormond Beach, FL
And you don't even mention Frank's name?
Rod
Re: Lust at first sight... jointer
Robin Corell in Atascadero CA
far be it from me to rain on anyones aircraft carrier dreams, but there is very little to be gained in an 18" over a nice 12" three toe, and three toed wedge beds come appart into lighter pieces.
You mean the big man in my shop?
Joanne in Point Pleasant, PA
Sorry, I couldn't find the pics when I was posting. I have switched over to a Mac at home and couldn't find the pc's backup disc. Kind of you to remember, Rod. Here he is!



Oh My . . .
Mark Mandell - Gone Round In New Jersey
Do they make a Shelix head for that?
At $725
Mark Mandell - Gone Round In New Jersey
I be sorely tempted as well.
Wonder if it would run well on a 3hp single phase 220 motor?
Re: 3hp
Joanne in Point Pleasant, PA
Hmmm. Frank is a 16" and he's got a 5hp single phase 220. I think it's a 5hp, anyway. I'll look tomorrow.
Still in the Articles section…
Rod Peterson—Ormond Beach, FL
I remember processing it:
Meet “Frank”, a 16" Jointer.
http://woodcentral.com/articles/powertools/articles_768.shtml
Rod
Yes, Joanne…
Rod Peterson—Ormond Beach, FL
5 HP. It's in the article...
Rod
Re: You mean the big man in my shop?
Larry in nw ohio
Joanne I read your article on getting and cleanning up the new old man in your life. Absolutly great and very envious. I wish I could do something like that but shop is already full. But we did have one at the place I worked at for over 30 years and it looked just nlike Frank. When it was turned on, a person would know it at the other side of the plant. It had a sound all it`s own, it was such a beautiful sound. It really surprized me how little we needed to rebabbit it. Enjoy it. Larry
Re: Still in the Articles section…
Joanne in Point Pleasant, PA
Ahhh. Thanks, Rod! I was looking for that. I couldn't remember if it was a big Shop Shot or in Articles. I had gone through the Shop Shots looking and ran out of time before leaving for work.
Justification for building a shop?