Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Do you turn with a face shield?

Posts

Do you turn with a face shield?

#1

Do you turn with a face shield?

Mike Rubes, Apex, NC

This is about as informal as it gets, but given the discussions below, I am curious as to people's responses.

I personally wear my face shield about 99% of the time when actualy turning. It is just one of the "standard" $30 ones from Woodcraft. I don't think it will give very much protection if a big chunk of wood comes off the lathe, but it is a LOT more protection than just my face :) I once had a bowl break when it was already very thin and one of those pieces bounced off the shield, so it worked for that very lightweight piece. However, I very seldom wear it when sanding. If you don't wear one, it seems like you have to be very aware of where the shavings are going so they don't hit your face. With the shield on, I never worry about the shavings, but concentrate on my tool and how it working the wood and let the shavings go where they may. I see it as three categories:

1) Wear the face shield almost all of the time (>99%)

2) Wear the face shield only sometime

3) Wear the face shield almost none of the time (<99%)

I would think that most people fall into the first category, but I could be wrong.

Anyway, just curious about any responses.

Mike

Thinking about wearing my motorcycle helmet when roughing in Apex, NC.

Re: Do you turn with a face shield?

#2

Re: Do you turn with a face shield? 1.2

George Guadiane

I'm closer to 80+%

If I'm hollowing, off the end and not in the line of fire, I tend to at least lift the visor.

I'm sure that anything between us and a flying piece of wood will lessen the damage done to us.

Re: Do you turn with a face shield?

#3

JL

Re: Do you turn with a face shield?

JL

It depends.

If I am turning spindles, then no. I usually don't wear a face shield. Dust mask and safety glasses - but not a face shield.

If I am turning bowls, then yes - about 50% of the time or more. Also safety glasses and dust mask.

Re: Do you turn with a face shield?

#4

Steven Antonucci

Admittedly, not always

steven antonucci

For me, when I turn with a faceshield on, it is usually because I cannot stand in a particular way that allows me to direct the shavings away from my face, and I don't have any choice. I am not advocating that other people do not use one, but I often find myself wearing only safety goggles to keep the fine dust out of my eyes.

My issue with using one is that I find the face shield extremely difficult to see through. It's either fogging or attracting fine dust, making me strain to see what I am doing. I have been struck in the faceshield with a bowl or platter that disintegrated, and I will say that a faceshield is meant to redistribute the force and functioned very well in that incident. Instead of a hammer to the face, it was a hard slap. In retrospect, I shouldn't have been standing where I was, and the bowl wouldn't have hit me.

All new turners should wear them all of the time, and most experienced turners should probably also. They are not eye protection. That said, it is very hard to demonstrate with one on...

Steven

Re: Do you turn with a face shield?

#5

Re: Admittedly, not always

John Lucas

Steve and I are in the same boat. I almost never wear one. I can't stand them. I can't see through them. I do wear them when I am rough turning or as Steve stated anytime I have to make a cut that throws chips my way.

I have been experimenting with the various scrapers lately and you simply have to wear them with those because it throws shaving right in your face. One of the reasons I'm not partial to them.

Granted a lot of what I turn is simply not very dangerous. It's either small, or very stable dry wood or spindles. When turning hollow vessels I do wear one fairly often for turning the outside but when I turn the inside I'm standing well out of the line of fire, or line of trajectory if you wish, and simply don't want to put up with the annoyance of the face shield. The same with bowls. I may or may not wear one when turning the outside depending on where I can stand and the size of the wood. I seldom wear one when hollowing the bowl, again because I'm standing at the end and don't see how the wood could possibly hit me if it blows up.

Sooner or later I guess I'll pay the price. I'm trying very hard to convince myself to buy a respirator or powered face shield because I think the dust will eventually do me in. However I can't stand the thought of going into the shop and having to dress like a guy going into a Nuclear reactor. It's just one of those things I've got to get over.

Re: Do you turn with a face shield?

#6

Re: Do you turn with a face shield?

Wally Dickerman in Arizona

I had been turning for at least 40 years before I even knew that there was such a thing as a face shield and that a lot of turners used one. I got one and didn't like it at all. Still don't. I do wear it when I'm rough turning a burl or something else that might bust off and smack me.

After about 70 years of turning I can't remember ever being hit with anything large enough to do damage. I used to turn a lot of big burls but not any more.

I learned long ago to stay out of the line of fire but of course that's not always easy to do.

Many will say that I've been more than lucky and I agree with them.

I do always wear safety glasses and usually a hat. Been thinking about getting a hard hat.

Re: Do you turn with a face shield?

#7

Re: Admittedly, not always

gary clarke

I wear a face mask and helmut 100% of the time and have been turning for 10 + yrs. I had surgery on one eye before I started turning and I do not want to even think of having any more eye surgery, why take a chance? The air circulation in the helmut helps to keep my face and glasses free of moisture, dust and fog. An ounce of prevention is worth 100 lbs of cure.

Re: Do you turn with a face shield?

#8

always

D. Hansen

first I put on the face shield (powered) then the lathe. I'm chicken and hurt easily. It only takes a second and I can't see anyway so the shield does not interfere :))

Re: Do you turn with a face shield?

#9

ALWAYS!

bob davis

Re: Do you turn with a face shield?

#10

Dick Hines

Re: ALWAYS!

Dick Hines

I wear mine when roughing out hollow forms and bowls. Not when hollowing and finishing bowls.

Mainly to keep the shavings out of my face.

Re: Do you turn with a face shield?

#11

Walt Bennett

#3, but I've safety glasses

Walt Bennett

Re: Do you turn with a face shield?

#12

Re: Do you turn with a face shield?

robo hippy

I don't use one except when turning spindles, which most of the time are rolling pins. I can't seem to be able to find a way to stand out of the line of fire and don't like the shavings in the face.

On bowls, never. I stand out of the line of fire. The only time I get shavings in the face, is when coring. Seems that the McNaughton always throws them straight into my face. Hand in front makes a good shield. When roughing bowls with scrapers, I stand a bit to the side. Shavings go up and over my hand, and out of my way. I always stand out of the line of fire.

robo hippy

Re: Do you turn with a face shield?

#13

Bob Moffett

Re: Do you turn with a face shield?

Bob Moffett

Always

Re: Do you turn with a face shield?

#14

Only when roughing... 

Doug Thompson near Cleveland

Re: Do you turn with a face shield?

#15

Re: Do you turn with a face shield?

Randy Gleckler

Put me in the 99% of the time yes category. There's a very very rare occasion I don't. Has nothing to do with Shavings, or line of fire. I just don't want anything happening to my gorgeous face. :-D

Re: Do you turn with a face shield?

#16

Don Geiger

Re: Do you turn with a face shield?

Don Geiger

Absolutely! I have been turning a long time and turn a lot. I can not think of any good reason NOT to wear one all the time.

I wear the Bios Shield. It is quite comfortable and I have the clear non-fogging face shield. I feel like the little extra protection the Bios gives me down in front of my throat will pay off one day. I can't imagine the damage that would occur if I was hit in the throat with a piece of wood.

Don Geiger

Re: Do you turn with a face shield?

#17

Re: Do you turn with a face shield?

ccourt9283

Yes. I am a believer.

About 4 years ago a I was roughing out a spalted piece between centers when it broke and hit me in the face. My face shield prevented me from serious injury although I ended up with 2 black eyes and 9 external stitches. The center tab that attached the clear face shield cut my forehead and eyebrow. Scared the sxxt out of me. I lucky not to have a drool cup. I won't turn on the lathe without my face shield now.

Re: Do you turn with a face shield?

#18

Re: Do you turn with a face shield?

Bob Lalonde

I could do better. I usually use a face shield when roughing out a larger out of balance piece. Like some of the others, I have trouble seeing if it get dirty and wet - no excuse though. I have started turning more slowly even though it takes longer.

Re: Do you turn with a face shield?

#19

Richard Allen

Almost never

Richard Allen

I almost never wear a face shield.

I have tried many different face shield in the 12+ years I have been turning wood. All of them have obstructed my view. I have never felt safer wearing a face shield.

Get out of the line of fire.

Re: Do you turn with a face shield?

#20

Re: Do you turn with a face shield?

Jorge Casta�eda

Mike,

I use it when rouging and coring, I don't the rest of the time, I manage to fog it, so if the stuff is not flying at me, I do without. When shaping I can put the shavings wherever I want, I aim to a cardboard box and when fill it goes to a 40 gal garbage bag.

Perhaps a face shield with air pumped into it would be good for me.

I do use a respirator always when sanding and at all times regardless of activity I am wearing OSHA certified prescription shop glasses.

I like the idea of the motorcycle helmet.

Re: Do you turn with a face shield?

#21

Mike Mills

Re: Do you turn with a face shield?

Mike Mills

Guess I fall into the 99%.

For small light work I sometimes I wear only safety glasses at other times my lightweight face shield.

Most (75%) of the time I wear my heavy weight face shield (ballistic grade).

Re: Do you turn with a face shield?

#22

Re: Do you turn with a face shield?

Carole Valentine

About 75% of the time when turning, never when sanding. That 25% will get me some day! Until I got my Uvex, I never wore one...couldn't stand them. The Uvex is perfect..., comfortable, good view and does not fog (provided you get the anti-fog model). It covers my throat and the front of my head. My glasses are safety glasses.

I am getting better remembering to put it on every time I read of an accident, so keep reporting them folks!

Re: Do you turn with a face shield?

#23

Re: Do you turn with a face shield? Always

Ed Larson

Re: Do you turn with a face shield?

#24

Re: Do you turn with a face shield?

Bill Gasper

Almost 99% of the time. Always with safety glasses, with or without the shield. When sanding I use a powdered respirator.

Re: Do you turn with a face shield?

#25

Lyle Jamieson

Re: Do you turn with a face shield?

Lyle Jamieson

At home I have it on all the time. I feel naked when I do demos and I have to project my voice to the audience and demo without my face shield. I am pleased to see the large number of folks using face shields. This is not a testosterone thing this has life or death possibilities

Stance and line of sight is important to turning successful shapes. Shavings in your face can hurt, a chunk of wood can kill you. Sure the danger zone has the most risk, but if a vessel flies apart and hits the tool rest, banjo, or lathe bed it could get flung anyplace. I have seen pieces stuck in the ceiling, what if it broke a light and you were showered with splintered glass from that 8 foot long light above your lathe??

It gets dirty, clean it!! A used dryer fabric softener sheet will retard the static. Foggy?? Pull it slightly away from your mouth/nose. These are not good excuses to not use a face shield, get over it.

You are not using a table saw or drill press where sawdust is flying in your face, safety glasses are no help for flying objects.

You can do everything right and still get hurt. Wood has unpredictable faults and invisable flaws. And you want to push your luck and turn S***ty wood full of cracks??