Re: Who's Tim? And how to I contact him?
gil jones
Donna,
Tim Geist
Teknatool (Nova) Rep for USA
304-295-8166 or tvgeistmfg@aol.com
Gil
Knowledge You Can Build On — Est. 1998
Re: Who's Tim? And how to I contact him?
gil jones
Donna,
Tim Geist
Teknatool (Nova) Rep for USA
304-295-8166 or tvgeistmfg@aol.com
Gil
Re: Who's Tim? And how to I contact him?
Donna Parrillo
Thank you Gil.
welcome
gil jones
Re: Well of course
Don at Central Illinois
I had an ag teacher in HS that told us (tongue in cheek) that we all needed to know how to the proper tool for the job. Example, never use a big wrench for a hammer, when a smaller wrench will do.
Re: Well of course
Harry in Beautiful Downtown Kulpsville
I was at a Nick Cook demo a couple weeks ago. He told us a saying attributed to Rudy Osolnik. "Every tool is a hammer, except a chisel. And they are screwdrivers."
Does not make sense
Wilford Bickel
This solution does not make sense to this engineer. I quit buying Teknatool products when they moved production to PRC. When my NZ chucks wear out I'll find another brand to replace my big chucks with at that time- as good as my NZ ones are and with proper maintenance I may never see that day! I just went out to the shop and studied my NZ Supernova and Supernova 2 chucks. How can the clip that is in the center cause the gear ring in the outside to be dragging on the plastic cover? The outside edge of the cover sits on a cut lip on the main chuck body. I have had my two SN2's long enough they have even had the backs pulled and the grease removed and replaced so I have seen inside them and none of this makes sense. If the clip is too thick it will not fit in the groove (if the groove is machined properly). Also it would keep the grub screw that holds the insert in from going in the hole as it would have the hole for the grub screw depressed and prevent insertion of the screw unless they have changed that design. Sorry folks but I am not buying this one unless someone can explain it to me better.
Re: Does not make sense
Jeff Willaford
I'm no engineer but I know changing the clip worked for me. I'm guessing the clip pressed down on the center of the plastic back more than it should. This might have caused extra pressure on the 'saddle' or U that holds the pinions in place. If so, I guess it could cause the pinion to be hard to turn. In my case removing the clip entirely allowed the scroll to turn freely as it should and it still worked that way after putting the new clip in. I'm just taking my best guess at why it made a difference here. The actual engineering answer would have to come from Teknatool or someone else.
Re: Does not make sense
Carole Valentine
Ditto what Jeff said. I don't know about "engineering sense" cause I have very little of that, but I found that it did solve the problem on the 4 new chucks we were working with. If we put the old clips back in, the problem returned. If I put the clip from one of the new chucks on one of my old SN2s, it got stiff. Without taking one apart again, it looks like the clip, when in place, fits under the upper edge of the machined groove and rests directly on top of the inner rim of the backer plate. If it presses too hard the saddles of the plate put pressure on the pinions which apparently causes the stiffness. The difference in the thickness of the clips was .14 mm. All of this has no effect on the grub screws.
Re: Does not make sense
Wilford Bickel
Carole - are you saying the clip is not seating in the groove but just holding by catching the outer lip? If so this could be a very dangerous situation as it could allow the clip to come off while in use. I know of one Teknatool Compac chuck (have one myself so I keep a constant watch for this and mine has been fine) that had the clip come off due to the clip not seating in the groove and allow the chuck to fly apart - jaws, slides, etc. going across the shop at high rpm. This may be a more serious and possibly dangerous situation then just the chuck being hard to use. If this is the case I would not use any of the new chucks that had this problem till they were repaired and the clips were seating in the groove completely! Is there any play in the new clip along the spindle axis after replacement? This could also be a problem with the clip giving, these type of clips are supposed to be machined to fit the groove with very close tolerances. If I owned one of these chucks I would want to know if the groove was cut wrong or if the clip was too thick - this would determine if I kept the chuck or returned it and went to another brand for safety.
Re: Does not make sense
gil jones
The cir-clip sits IN a grove.
The c-clips don't change much on SN2
Chuck Jones - West TN
I received the two c-clips Tom Geist sent as replacements for my latest SN2 chucks and I replaced the one on the chuck I bought in March. I cannot tell one bit of difference. The gears still feel very rough. As far as the tightness is concerned that was already getting better with use. Both of the two stamped �PRC� are noticeably rougher than the NZ version I bought in July 2007. I can sit it on the table and spin the hex tool with ease with one finger and thumb; smooth as silk. That�s certainly not the case with either of the two newer ones. We may as well face facts. The Chinese versions are poorer quality.
As a practical matter all three chucks seem to work fine. The difference is not enough for me to incur the frustration of pursuing the issue further or returning the chucks. It�s just that now I will view the SN2 as a cheap, reasonably workable Chinese-made commodity tool; not a slightly more expensive high quality tool like the earlier SN2�s. There is no longer a reason to favor the SN2 over other cheaper products. This will of course affect my attitude about any Technatool product.
Why oh why
Wayne K
Do these corporate accountants keep ruining a quality product?
This chuck had the best advertising money can't buy, word of mouth from highly satisfied users.
"But we can manufacture this fine product in china, save a boatload of cost and sell it slightly cheaper and we put more cash in our pocket. It will be slightly lesser quality but Nobody will notice, if they do screw 'em."
It makes me sick.
Wayne Kuhn
Owner of one real SN2 and one fake Chinese sn2.
send them back
Jeff Willaford
If the quality is not up to standard then you should send them back rather than keep chucks you are not happy with IMHO. The only way Teknatool and whoever you bought them from will know about the quality issues is if you tell them and returning them is the best way to let them know. The retailer should pay the shipping for the return.
Fortunately for me the clip did fix my SN2 but I don't hesitate to return something if the quality is not there or if the item if very much different than described.
Re: Why oh why
bill crommett
Just be happy that Tecknatool doesn't have any Chinese dry wall in the chucks.
Gotta give Technatool/Tim Geist credit...
Chuck Jones - West TN
I sent Tim a message yesterday evening (worded same as my previous post). He was on the phone by noon today to discuss what else they can do to make things right.
Like I said before... anyone can screw up, it's how they respond that counts.
Re: Gotta give Technatool/Tim Geist credit...
Dick Hines
I will bet you that Teknatool would like this problem with the SN2 chucks to be fix too. They sell a ton of these chucks and the problem they have with the clips is giveing the one big pain in the butt. The chucks are a great product and people like them. So I am sure they are doing some big time problem solveing.